AD9371 系列快速入口
AD9371+ZCU102 移植到 ZCU106 ： AD9371 官方例程构建及单音信号收发
ad9371_tx_jesd -->util_ad9371_xcvr接口映射： AD9371 官方例程之 tx_jesd 与 xcvr接口映射
AD9371 官方例程 时钟间的关系与生成 ： AD9371 官方例程HDL详解之JESD204B TX侧时钟生成（一）
AD9371 官方例程 时钟间的关系与生成 ： AD9371 官方例程HDL详解之JESD204B TX侧时钟生成 （二）
采样率和各个时钟之间的关系 ： AD9371 官方例程HDL详解之JESD204B TX侧时钟生成 （三）
参考：
AD9371/AD9375 No-OS Setup
文章目录
- 前言
- 一、myk_ad9528init
- 二、myk.c
前言
SDK或者vitis 裸机程序需要配置 AD9528、AD9371、FPGA相关IP等，根据自己项目需求，可以通过 MATLAB Profile Generator 和 Transceiver Evaluation Software 生成所需的 myk.c, myk.h and myk_ad9528init.c 文件来替换
一、myk_ad9528init
AD9528 初始化文件
SPI 设置，通过SPI配置AD9528参数
1, //chip select Index ，AD9371 是 2，用于SPI 片选 spi_csn，ZYNQ只使用了 SPI0来配置9528和9371
static spiSettings_t clockSpiSettings = {
1, //chip select Index
0, //Write bit polarity
1, //16bit instruction word
1, //MSB first
0, //Clock phase
0, //Clock polarity
0,//uint8_t enSpiStreaming;
1,//uint8_t autoIncAddrUp;
1 //uint8_t fourWireMode;
};
PLL1 相关配置
30720000，AD9258 PLL1 配置，refA 的频率
122880000，vcxo 频率，ADRV9371 板载的 122.88M
ad9528pll1Settings_t clockPll1Settings = {
30720000,
1,
3,
0,
1,
0,
122880000,
2,
4
};
PLL2 相关配置
3，PLL2的M1，可选 3，4，5
PLL2的N2，应该为 10 ，这样 122.88M x 3 x 10 = 3.6864G ，满足PLL2的VCO工作频率 3.450 GHz 到 4.025 GHz
但没关系 ，主函数中的函数 AD9528_initDeviceDataStruct(clockAD9528_device,vcxo_Frequency,refA_Frequency,outFrequency[1])
会重新计算 PLL1 、 PLL2 和 SYSREF 的各个参数，得到 pll2Settings->n2Divider = 10
ad9528pll2Settings_t clockPll2Settings = {
3,
30
};
53237，00 1111 1111 0101，0 使能对应的OUT输出，53237 即 使能 OUT 1、3(SYSREF)、12(SYSREF)、13
{0,0,0,2,0,0,0,0,0,0,0,0,2,0}, 9528 OUT输出信号源 选择 outSource[3] = SYSREF;outSource[12] = SYSREF;
0，选择PLL2 经过 分频器 CHANNEL_DIV 产生信号
2，选择SYSREF generation 电路产生的 SYSREF 信号输出
最后一行是AD9528产生的 14路 输出信号频率，对于 ADRV9371 来说，使用了 OUT 1、3(SYSREF)、12(SYSREF)、13
outFrequency_Hz[1] 一定要设置成想得到的频率，以在 AD9528_initDeviceDataStruct 中使用，来计算各种参数
ad9528outputSettings_t clockOutputSettings = {
53237,
{0,0,0,2,0,0,0,0,0,0,0,0,2,0},
{0,0,0,0,0,0,0,0,0,0,0,0,0,0},
{0,0,0,0,0,0,0,0,0,0,0,0,0,0},
{0,0,0,0,0,0,0,0,0,0,0,0,0,0},
{10,10,10,10,10,10,10,10,10,10,10,10,10,10},
{122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000, 122880000}
};
0，SPI，SYSREF requested 通过SPI请求 SYSREF ， 1 通过 引脚
2，SYSREF 生成模式 ，2 内部产生，即 Mode 3 Internal
0，sysrefPatternMode_t，SYSREF 生成模式， N-shot = 0, CONTINUOUS = 1, PRBS = 2, STOP = 3
0，sysrefNshotMode_t ，SYSREF 输出脉冲数， ONE_PULSE = 0, TWO_PULSES = 2, FOUR_PULSES = 3
512， 16-bit K 分频 ，0 到 65535， 有一个固定 2分频，即最终分频 2 x k，如输入信号122.88M，SYSREF = 122.88M/（2 x 512）= 0.12 MHz ，得到SYSREF 频率为 120000， OUT 3 和 12 输出 0.12M 的 SYSREF 信号
ad9528sysrefSettings_t clockSysrefSettings = {
0,
2,
0,
0,
0,
0,
512
};
myk_ad9528init文件 VCXO、REFA、outFrequency_Hz[1] 一定要设置对， PLL1、 PLL2、 SYSREF、Output 参数可以通过函数AD9528_initDeviceDataStruct 得到
二、myk.c
AD9371 初始化
AD9371内 TX 滤波器具体系数
static int16_t txFirCoefs[]
txFir 滤波器具体配置
6，滤波器增益
32, 使用多少抽头系数
static mykonosFir_t txFir = {
6, /* Filter gain in dB*/
32, /* Number of coefficients in the FIR filter*/
&txFirCoefs[0] /* A pointer to an array of filter coefficients*/
};
rx、obsrx、sniffer 同上
AD9371 RX 信号组帧配置，obsRxFramer 类似
2T2R，4个转换器，多帧有32个帧，解扰，使用外部 SYSREF 信号，0x03, 使用最低两个lane传输数据，
0 ，bitRepeat mode，RX 和 RX_OS（嗅探） 各自使用一个组帧器，采样率可以不一样，使用 Bit repeat 模式做到
0 ，/* Selects SYNCb input source，0 使用SYNCINB0（连到RX） ， 1 使用SYNCINB1（连到OBSRX）
static mykonosJesd204bFramerConfig_t rxFramer = {
0, /* JESD204B Configuration Bank ID -extension to Device ID (Valid 0..15)*/
0, /* JESD204B Configuration Device ID - link identification number. (Valid 0..255)*/
0, /* JESD204B Configuration starting Lane ID. If more than one lane used, each lane will increment from the Lane0 ID. (Valid 0..31)*/
4, /* number of ADCs (0, 2, or 4) - 2 ADCs per receive chain*/
32, /* number of frames in a multiframe (default=32), F*K must be a multiple of 4. (F=2*M/numberOfLanes)*/
1, /* scrambling off if framerScramble= 0, if framerScramble>0 scramble is enabled.*/
1, /* 0=use internal SYSREF, 1= use external SYSREF*/
0x03, /* serializerLanesEnabled - bit per lane, [0] = Lane0 enabled, [1] = Lane1 enabled*/
0xE4, /* serializerLaneCrossbar*/
22, /* serializerAmplitude - default 22 (valid (0-31)*/
4, /* preEmphasis - < default 4 (valid 0 - 7)*/
0, /* invertLanePolarity - default 0 ([0] will invert lane [0], bit1 will invert lane1)*/
0, /* lmfcOffset - LMFC_Offset offset value for deterministic latency setting*/
0, /* Flag for determining if SYSREF on relink should be set. Where, if > 0 = set, 0 = not set*/
0, /* Flag for determining if auto channel select for the xbar should be set. Where, if > 0 = set, '0' = not set*/
0, /* Selects SYNCb input source. Where, 0 = use RXSYNCB for this framer, 1 = use OBSRX_SYNCB for this framer*/
0, /* Flag for determining if CMOS mode for RX Sync signal is used. Where, if > 0 = CMOS, '0' = LVDS*/
0, /* Selects framer bit repeat or oversampling mode for lane rate matching. Where, 0 = bitRepeat mode (changes effective lanerate), 1 = overSample (maintains same lane rate between ObsRx framer and Rx framer and oversamples the ADC samples)*/
0 /* Flag for determining if API will calculate the appropriate settings for framer lane outputs to physical lanes. Where, if '0' = API will set automatic lane crossbar, '1' = set to manual mode and the value in serializerLaneCrossbar will be used*/
};
AD9371 TX 信号解帧配置
2T2R，4个转换器，多帧有32个帧，加扰，使用外部 SYSREF 信号，0x0F, 使用全部 4 个lane传输数据，
0, /* LMFC_Offset offset，0…31，通过 LMFC 偏移调整确定性延迟
static mykonosJesd204bDeframerConfig_t deframer = {
0, /* bankId extension to Device ID (Valid 0..15)*/
0, /* deviceId link identification number. (Valid 0..255)*/
0, /* lane0Id Lane0 ID. (Valid 0..31)*/
4, /* M number of DACss (0, 2, or 4) - 2 DACs per transmit chain */
32, /* K #frames in a multiframe (default=32), F*K=multiple of 4. (F=2*M/numberOfLanes)*/
1, /* scramble scrambling off if scramble= 0.*/
1, /* External SYSREF select. 0 = use internal SYSREF, 1 = external SYSREF*/
0x0F, /* Deserializer lane select bit field. Where, [0] = Lane0 enabled, [1] = Lane1 enabled, etc */
0xE4, /* Lane crossbar to map physical lanes to deframer lane inputs [1:0] = Deframer Input 0 Lane section, [3:2] = Deframer Input 1 lane select, etc */
1, /* Equalizer setting. Applied to all deserializer lanes. Range is 0..4*/
0, /* PN inversion per each lane. bit[0] = 1 Invert PN of Lane 0, bit[1] = Invert PN of Lane 1, etc).*/
0, /* LMFC_Offset offset value to adjust deterministic latency. Range is 0..31*/
0, /* Flag for determining if SYSREF on relink should be set. Where, if > 0 = set, '0' = not set*/
0, /* Flag for determining if auto channel select for the xbar should be set. Where, if > 0 = set, '0' = not set*/
0, /* Flag for determining if CMOS mode for TX Sync signal is used. Where, if > 0 = CMOS, '0' = LVDS*/
0 /* Flag for determining if API will calculate the appropriate settings for deframer lane in to physical lanes. Where, if '0' = API will set automatic lane crossbar, '1' = set to manual mode and the value in deserializerLaneCrossbar will be used*/
};
RX 增益初始配置，orxGainControl 和 snifferGainControl 类似
MGC ，手动增益控制 ，AGC 自动增益控制
RSSI ，Rx1 RSSI 和 Rx2 RSSI
static mykonosRxGainControl_t rxGainControl = {
MGC, /* Current Rx gain control mode setting*/
255, /* Rx1 Gain Index, can be used in different ways for manual and AGC gain control*/
255, /* Rx2 Gain Index, can be used in different ways for manual and AGC gain control*/
255, /* Max gain index for the currently loaded Rx1 Gain table*/
195, /* Min gain index for the currently loaded Rx1 Gain table*/
255, /* Max gain index for the currently loaded Rx2 Gain table*/
195, /* Min gain index for the currently loaded Rx2 Gain table*/
0, /* Stores Rx1 RSSI value read back from the Mykonos*/
0 /* Stores Rx2 RSSI value read back from the Mykonos*/
};
RX 自动增益 Peak threshold 模式参数配置 ，obsRxPeakAgc 类似
static mykonosPeakDetAgcCfg_t rxPeakAgc = {
0x26, /* apdHighThresh: */
0x16, /* apdLowThresh */
0xB5, /* hb2HighThresh */
0x72, /* hb2LowThresh */
0x40, /* hb2VeryLowThresh */
0x06, /* apdHighThreshExceededCnt */
0x04, /* apdLowThreshExceededCnt */
0x06, /* hb2HighThreshExceededCnt */
0x04, /* hb2LowThreshExceededCnt */
0x04, /* hb2VeryLowThreshExceededCnt */
0x4, /* apdHighGainStepAttack */
0x2, /* apdLowGainStepRecovery */
0x4, /* hb2HighGainStepAttack */
0x2, /* hb2LowGainStepRecovery */
0x4, /* hb2VeryLowGainStepRecovery */
0x1, /* apdFastAttack */
0x1, /* hb2FastAttack */
0x1, /* hb2OverloadDetectEnable */
0x1, /* hb2OverloadDurationCnt */
0x1 /* hb2OverloadThreshCnt */
};
RX 自动增益 Power Measurement 模式参数 ， obsRxPwrAgc 类似
static mykonosPowerMeasAgcCfg_t rxPwrAgc = {
0x01, /* pmdUpperHighThresh */
0x03, /* pmdUpperLowThresh */
0x0C, /* pmdLowerHighThresh */
0x04, /* pmdLowerLowThresh */
0x4, /* pmdUpperHighGainStepAttack */
0x2, /* pmdUpperLowGainStepAttack */
0x2, /* pmdLowerHighGainStepRecovery */
0x4, /* pmdLowerLowGainStepRecovery */
0x08, /* pmdMeasDuration */
0x02 /* pmdMeasConfig */
};
RX AGC 配置 ，obsRxAgcConfig 类似
1, /* agcObsRxSelect ， 1 选择 Sniffer
1, /* agcPeakThresholdMode ，1，Peak Threshold
static mykonosAgcCfg_t rxAgcConfig = {
255, /* agcRx1MaxGainIndex */
195, /* agcRx1MinGainIndex */
255, /* agcRx2MaxGainIndex */
195, /* agcRx2MinGainIndex: */
255, /* agcObsRxMaxGainIndex */
203, /* agcObsRxMinGainIndex */
1, /* agcObsRxSelect */
1, /* agcPeakThresholdMode */
1, /* agcLowThsPreventGainIncrease */
30720, /* agcGainUpdateCounter */
3, /* agcSlowLoopSettlingDelay */
4, /* agcPeakWaitTime */
0, /* agcResetOnRxEnable */
0, /* agcEnableSyncPulseForGainCounter */
&rxPeakAgc,
&rxPwrAgc
};
根据 Profile 文件 ，配置 rx、orx、sniffer、tx 的 IQ采样率 、信号带宽 、抽取或者内插系数、滤波器系数等
static mykonosTxProfile_t txProfile = {
/* Tx 20/100MHz, IQrate 122.88MSPS, Dec5 */
DACDIV_2p5, /* The divider used to generate the DAC clock*/
&txFir, /* Pointer to Tx FIR filter structure*/
2, /* The Tx digital FIR filter interpolation (1,2,4)*/
2, /* Tx Halfband1 filter interpolation (1,2)*/
1, /* Tx Halfband2 filter interpolation (1,2)*/
1, /* TxInputHbInterpolation (1,2)*/
122880, /* Tx IQ data rate in kHz*/
20000000, /* Primary Signal BW*/
100000000, /* The Tx RF passband bandwidth for the profile*/
710539, /* The DAC filter 3dB corner in kHz*/
50000, /* Tx BBF 3dB corner in kHz*/
0 /* Enable DPD, only valid for AD9373*/
};
9371 参考时钟
122.88M ，AD9525 OUT 13输出到9371的 DEV_CLK（E7 E8） ， DEV_CLK参考时钟频率 10 MHz 到 320 MHz.
9830400 ，PLL VCO 工作频率，在 6 GHz 到 12 GHz
2，VCO divider，1，1.5，2，3， hsclkRate= clkPllVcoFrequency / VCO divider
4，HS Divider，4 或 5，hsDigClk = hsclkRate/ hsDiv
static mykonosDigClocks_t mykonosClocks = {
122880, /* CLKPLL and device reference clock frequency in kHz*/
9830400, /* CLKPLL VCO frequency in kHz*/
VCODIV_2, /* CLKPLL VCO divider*/
4 /* CLKPLL high speed clock divider*/
};
RX 配置，txSettings 类似，Tx Attenuation ，衰减步长 和 衰减 mdB
RX1_RX2，初始化 RX 1 和 2
0, / Internal LO = 0, 本振使用内部产生的
2.5G，Rx PLL 本振频率 ，2.5GHz
0 ， / 0，复数，1 实数
static mykonosRxSettings_t rxSettings = {
&rxProfile, /* Rx datapath profile, 3dB corner frequencies, and digital filter enables*/
&rxFramer, /* Rx JESD204b framer configuration structure*/
&rxGainControl, /* Rx Gain control settings structure*/
&rxAgcConfig, /* Rx AGC control settings structure*/
RX1_RX2, /* The desired Rx Channels to enable during initialization*/
0, /* Internal LO = 0, external LO*2 = 1*/
2500000000U, /* Rx PLL LO Frequency (internal or external LO)*/
0 /* Flag to choose if complex baseband or real IF data are selected for Rx and ObsRx paths. Where, if > 0 = real IF data, '0' = zero IF (IQ) data*/
};
OBS_RX 配置，
MYK_ORX1_ORX2 | MYK_SNRXA_B_C，初始化 ORX1、ORX2、SNRXA、B、C
OBSLO_TX_PLL， Obs Rx 本振，0 本振由 Tx 产生， 1 本振由Sniffer 产生
2.6G，SnRx PLL 本振频率 ，2.6GHz
OBS_RXOFF ， ObsRx 通道关闭，后续主函数中配置使用OBS_RX1_SNIFFERLO
MYKONOS_setObsRxPathSource(&mykDevice,OBS_RX1_SNIFFERLO)
typedef enum{
OBS_RXOFF = 0,
OBS_RX1_TXLO = 1,
OBS_RX2_TXLO = 2,
OBS_INTERNALCALS = 3,
OBS_SNIFFER = 4,
OBS_RX1_SNIFFERLO = 5,
OBS_RX2_SNIFFERLO = 6,
OBS_SNIFFER_A = 0x14,
OBS_SNIFFER_B = 0x24,
OBS_SNIFFER_C = 0x34
}
static mykonosObsRxSettings_t obsRxSettings = {
&orxProfile, /* ORx datapath profile, 3dB corner frequencies, and digital filter enables*/
&orxGainControl,/* ObsRx gain control settings structure*/
&obsRxAgcConfig,/* ORx AGC control settings structure*/
&snifferProfile,/* Sniffer datapath profile, 3dB corner frequencies, and digital filter enables*/
&snifferGainControl,/* SnRx gain control settings structure*/
&obsRxFramer, /* ObsRx JESD204b framer configuration structure */
(MYK_ORX1_ORX2 | MYK_SNRXA_B_C),/* obsRxChannel */
OBSLO_TX_PLL, /* (obsRxLoSource) The Obs Rx mixer can use the Tx Synth(TX_PLL) or Sniffer Synth (SNIFFER_PLL) */
2600000000U, /* SnRx PLL LO frequency in Hz */
0, /* Flag to choose if complex baseband or real IF data are selected for Rx and ObsRx paths. Where if > 0 = real IF data, '0' = complex data*/
NULL, /* Custom Loopback ADC profile to set the bandwidth of the ADC response */
OBS_RXOFF /* Default ObsRx channel to enter when radioOn called */
};
SPI 参数配置
2， AD9371 是 2，9528 是1，用于SPI 片选 spi_csn，ZYNQ只使用了 SPI0来配置9528和9371
static spiSettings_t mykSpiSettings = {
2, /* chip select index - valid 1~8 */
0, /* the level of the write bit of a SPI write instruction word, value is inverted for SPI read operation */
1, /* 1 = 16-bit instruction word, 0 = 8-bit instruction word */
1, /* 1 = MSBFirst, 0 = LSBFirst */
0, /* clock phase, sets which clock edge the data updates (valid 0 or 1) */
0, /* clock polarity 0 = clock starts low, 1 = clock starts high */
0, /* Not implemented in ADIs platform layer. SW feature to improve SPI throughput */
1, /* Not implemented in ADIs platform layer. For SPI Streaming, set address increment direction. 1= next addr = addr+1, 0:addr=addr-1 */
1 /* 1: Use 4-wire SPI, 0: 3-wire SPI (SDIO pin is bidirectional). NOTE: ADI's FPGA platform always uses 4-wire mode */
};
DPD, CLGC, 和 VSWR 功能只有AD9375有，dpdConfig，clgcConfig，vswrConfig 不用管
后续 和 AD9371 交互并未通过GPIO ，armGpio，gpio3v3，gpio，mykonosAuxIo 不用管
温度传感器见 tempSensor、tempStatus
主函数 和 FPGA 中的相关 IP配置见下一节
