8080时序驱动液晶屏

news2024/11/25 1:43:34

一、TFT-LCD简介。

        TFT-LCD（thin film transistor-liquid crystal display）即薄膜晶体管液晶显示器。液晶显示屏的每一个像素上都设置有一个薄膜晶体管（TFT），每个像素都可以通过点脉冲直接控制，因而每个节点都相对独立，并可以连续控制，不仅提高了显示屏的反应速度，同时可以精确控制显示色阶，所以TFT液晶的色彩更真，因此TFT-LCD也被叫做真彩液晶显示器.

STM32F429 系列的芯片不需要额外的液晶控制器，也就是说它把专用液晶控制器的功能集成到 STM32F429 芯片内部了，可以理解为电脑的 CPU 集成显卡，它节约了额外的控制器成本。而 STM32F1 系列的芯片由于没有集成液晶控制器到芯片内部，所以它只能驱动自带控制器的屏幕，可以理解为电脑的外置显卡。
​

1.1 ILI9341液晶控制器简介

        本液晶屏内部包含有一个液晶控制芯片 ILI9341，它的内部结构非常复杂，该芯片最主核心部分是位于中间的 GRAM(Graphics RAM)，它就是显存。GRAM 中每个存储单元都对应着液晶面板的一个像素点。它右侧的各种模块共同作用把 GRAM 存储单元的数据转化成液晶面板的控制信号，使像素点呈现特定的颜色，而像素点组合起来则成为一幅完整的图像。

        框图的左上角为 ILI9341 的主要控制信号线和配置引脚，根据其不同状态设置可以使芯片工作在不同的模式，如每个像素点的位数是 6、16 还是 18 位；可配置使用 SPI 接口、8080 接口还是 RGB 接口与 MCU 进行通讯。MCU 通过 SPI、8080 接口或 RGB 接口与 ILI9341 进行通讯，从而访问它的控制寄存器 (CR)、地址计数器 (AC)、及 GRAM。 在 GRAM 的左侧还有一个 LED 控制器 (LED Controller)。LCD 为非发光性的显示装置，它需要借助背光源才能达到显示功能，LED 控制器就是用来控制液晶屏中的 LED 背光源。

​

 本文的显示屏使用8080端口通信。

1.2 硬件

 这里我用的是真的正点原子的显示屏

1.3 8080通信

 8080接口有5条基本的控制线和多条数据线（8/9/16/18位），它们的功能如下表：
在这里插入图片描述​

 8080接口模式的时序如下图所示：

在这里插入图片描述​

  • 在WR跳变为低电平后，液晶屏开始读取总线上面的数据
  • 在RD跳变为低电平后，液晶屏开始放置数据到总线上面

时序大概流程

其实就是根据时序图去控制几条控制线，一般的流程的，我们这里以写数据为例吧

  1. 开启片选，也就是打开CS=0（CS空闲是高电平的，所以我们置0才是打开）
  2. 选择对数据还是命令进行操作，这里我们是数据，所以RS=1（如果是命令就为0）
  3. 因为8080是并行的，我们可以读写并行，这里我们就不这样用了，所以直接先把读的控制线关闭了，把RD置为1。
  4. 打开写的控制线，也就是WR线置为0。
  5. 把我们的八位数据放在数据线上。
  6. 关闭写的控制线，WR置为1.
  7. 关闭片选，CS置为1，结束操作。

时序伪代码：

（1）读取数据：

LCD_CS = 0;		//开始片选  
LCD_RS = 1;		//数据操作
LCD_WR = 1;		//禁止写
LCD_RD = 0;		//上升沿读数据
data = DATAIN();//读取数据
LCD_RD = 1;		//上升沿读数据
LCD_CS = 1;		//结束片选

（2）写入数据：

LCD_CS = 0;			//开始片选  
LCD_RS = 1;			//数据操作
LCD_RD = 1;			//禁止读
DATAOUT(Data);		//输出数据
LCD_WR = 0;			//写入开始
LCD_WR = 1;			//写入结束
LCD_CS = 1;			//结束片选

 (3）读取命令：

LCD_CS = 0;		//开始片选  
LCD_RS = 0;		//命令操作
LCD_WR = 1;		//禁止写
LCD_RD = 0;		//上升沿读数据
data = DATAIN();//读取数据
LCD_RD = 1;		//上升沿读数据
LCD_CS = 1;		//结束片选

(4）写入命令： 

LCD_CS = 0;			//开始片选  
LCD_RS = 0;			//命令操作
LCD_RD = 1;			//禁止读
DATAOUT(Data);		//输出数据
LCD_WR = 0;			//写入开始
LCD_WR = 1;			//写入结束
LCD_CS = 1;			//结束片选

流程图如下

​

1.3 ILI9341指令格式说明

  ILI9341所有的指令都是8位的（高8位无效），且参数除了读写GRAM的时候是16位，其他操作参数，都是8位的。
  ILI9341的指令很多，这里不一一介绍，仅介绍几个重要的指令，他们是：0XD3，0X36，0X2A，0X2B，0X2C，0X2E等6条指令。
0XD3指令

  该指令为读ID4指令，用于读取LCD控制器的ID 。因此，同一个代码，可以根据ID的不同，执行不同的LCD驱动初始化，以兼容不同的LCD屏幕。
​

0X36指令

  I该指令为存储访问控制指令，可以控制ILI9341存储器的读写方向，简单的说，就是在连续写GRAM的时候，可以控制GRAM指针的增长方向，从而控制显示方式（读GRAM也是一样）。
在这里插入图片描述​

0X2A指令

  该指令是列地址设置指令，在从左到右，从上到下的扫描方式（默认）下面，该指令用于设置横坐标（x坐标）
在这里插入图片描述​

0X2B指令

  该指令是页地址设置指令，在从左到右，从上到下的扫描方式（默认）下面，该指令用于设置纵坐标（y坐标）
在这里插入图片描述​

0X2C指令

  该指令是写GRAM指令，在发送该指令之后，我们便可以往LCD的GRAM里面写入颜色数据了，该指令支持连续写 (地址自动递增)
在这里插入图片描述​

0X2E指令

  该指令是读GRAM指令，用于读取ILI9341的显存（GRAM），同0X2C指令，该指令支持连续读 (地址自动递增)

代码详解

这里我直接用库函数版本的了,这里的屏幕用的是正点2.4的板子，代码的话只适用于mini板子，因为mini板的芯片没有FSMC功能，所以直接用io口模拟时序，后面会出个FAMC的，这玩意写显示器的时序就简单多了，

#include "lcd.h"
#include "stdlib.h"
#include "font.h" 
//#include "usart.h"
#include "delay.h"	 


 
//LCD的画笔颜色和背景色
u16 POINT_COLOR=0x0000;     //画笔颜色
u16 BACK_COLOR=0xFFFF;      //背景色 

//管理LCD重要参数
//默认为竖屏
_lcd_dev lcddev;

//写寄存器函数
//data:寄存器值
void LCD_WR_REG(u16 data)
{ 
    LCD_RS_CLR;//写地址
    LCD_CS_CLR;
    DATAOUT(data);
    LCD_WR_CLR;
    LCD_WR_SET;
    LCD_CS_SET; 
}

//写数据函数
//可以替代LCD_WR_DATAX宏,拿时间换空间.
//data:寄存器值
void LCD_WR_DATAX(u16 data)
{
    LCD_RS_SET;
    LCD_CS_CLR;
    DATAOUT(data);
    LCD_WR_CLR;
    LCD_WR_SET;
    LCD_CS_SET;
}

//当mdk -O1时间优化时需要设置
//延时i
void opt_delay(u8 i)
{
    while (i--);
}

//读LCD数据
//返回值:读到的值
u16 LCD_RD_DATA(void)
{
    u16 t;
    GPIOB->CRL=0X88888888; //PB0-7  上拉输入
    GPIOB->CRH=0X88888888; //PB8-15 上拉输入
    GPIOB->ODR=0X0000;     //全部输出0

    LCD_RS_SET;
    LCD_CS_CLR;
    LCD_RD_CLR;

    opt_delay(2);
    t=DATAIN;  

    LCD_RD_SET;
    LCD_CS_SET; 

    GPIOB->CRL=0X33333333; //PB0-7  上拉输出
    GPIOB->CRH=0X33333333; //PB8-15 上拉输出
    GPIOB->ODR=0XFFFF;     //全部输出高
    return t;  
}

//写寄存器
//LCD_Reg:寄存器编号
//LCD_RegValue:要写入的值
void LCD_WriteReg(u16 LCD_Reg,u16 LCD_RegValue)
{
    LCD_WR_REG(LCD_Reg);  
    LCD_WR_DATA(LCD_RegValue);
}

//读寄存器
//LCD_Reg:寄存器编号
//返回值:读到的值
u16 LCD_ReadReg(u16 LCD_Reg)
{
    LCD_WR_REG(LCD_Reg);        //写入要读的寄存器号
    return LCD_RD_DATA();
}

//开始写GRAM
void LCD_WriteRAM_Prepare(void)
{
    LCD_WR_REG(lcddev.wramcmd);
} 
//LCD写GRAM
//RGB_Code:颜色值
void LCD_WriteRAM(u16 RGB_Code)
{
    LCD_WR_DATA(RGB_Code);      //写十六位GRAM
}

//从ILI93xx读出的数据为GBR格式，而我们写入的时候为RGB格式。
//通过该函数转换
//c:GBR格式的颜色值
//返回值：RGB格式的颜色值
u16 LCD_BGR2RGB(u16 c)
{
    u16  r, g, b, rgb;
    b = (c >> 0) & 0x1f;
    g = (c >> 5) & 0x3f;
    r = (c >> 11) & 0x1f;
    rgb = (b << 11) + (g << 5) + (r << 0);
    return (rgb);
}

//读取个某点的颜色值
//x,y:坐标
//返回值:此点的颜色
u16 LCD_ReadPoint(u16 x,u16 y)
{
    u16 r, g, b;

    if (x >= lcddev.width || y >= lcddev.height)return 0;   //超过了范围,直接返回

    LCD_SetCursor(x, y);

    if (lcddev.id == 0X5510)    //5510 发送读GRAM指令
    {
        LCD_WR_REG(0X2E00);
    }
    else                        //其他IC(9341/5310/1963/7789)发送读GRAM指令
    {
        LCD_WR_REG(0X2E);
    }

    r = LCD_RD_DATA();          //假读

    if (lcddev.id == 0X1963)    //对1963来说,是真读
    {
        return r;               //1963直接读就可以
    }

    r = LCD_RD_DATA();          //实际坐标颜色

    //9341/5310/5510/7789 要分2次读出
    b = LCD_RD_DATA();
    g = r & 0XFF;               //对于 9341/5310/5510/7789, 第一次读取的是RG的值,R在前,G在后,各占8位
    g <<= 8;
    return (((r >> 11) << 11) | ((g >> 10) << 5) | (b >> 11));  // 9341/5310/5510/7789 需要公式转换一下
}

//LCD开启显示
void LCD_DisplayOn(void)
{
    if (lcddev.id == 0X5510)    //5510开启显示指令
    {
        LCD_WR_REG(0X2900);     //开启显示
    }
    else                        //9341/5310/1963/7789 等发送开启显示指令
    {
        LCD_WR_REG(0X29);       //开启显示
    }
}

//LCD关闭显示
void LCD_DisplayOff(void)
{
    if (lcddev.id == 0X5510)    //5510关闭显示指令
    {
        LCD_WR_REG(0X2800);     //关闭显示
    }
    else                        //9341/5310/1963/7789 等发送关闭显示指令
    {
        LCD_WR_REG(0X28);       //关闭显示
    }
}

//设置光标位置
//Xpos:横坐标
//Ypos:纵坐标
void LCD_SetCursor(u16 Xpos, u16 Ypos)
{
    if (lcddev.id == 0X1963)
    {
        if (lcddev.dir == 0)   //x坐标需要变换
        {
            Xpos = lcddev.width - 1 - Xpos;
            LCD_WR_REG(lcddev.setxcmd);
            LCD_WR_DATA(0);
            LCD_WR_DATA(0);
            LCD_WR_DATA(Xpos >> 8);
            LCD_WR_DATA(Xpos & 0XFF);
        }
        else
        {
            LCD_WR_REG(lcddev.setxcmd);
            LCD_WR_DATA(Xpos >> 8);
            LCD_WR_DATA(Xpos & 0XFF);
            LCD_WR_DATA((lcddev.width - 1) >> 8);
            LCD_WR_DATA((lcddev.width - 1) & 0XFF);
        }

        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(Ypos >> 8);
        LCD_WR_DATA(Ypos & 0XFF);
        LCD_WR_DATA((lcddev.height - 1) >> 8);
        LCD_WR_DATA((lcddev.height - 1) & 0XFF);

    }
    else if (lcddev.id == 0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(Xpos >> 8);
        LCD_WR_REG(lcddev.setxcmd + 1);
        LCD_WR_DATA(Xpos & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(Ypos >> 8);
        LCD_WR_REG(lcddev.setycmd + 1);
        LCD_WR_DATA(Ypos & 0XFF);
    }
    else     //9341/5310/7789等设置坐标
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(Xpos >> 8);
        LCD_WR_DATA(Xpos & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(Ypos >> 8);
        LCD_WR_DATA(Ypos & 0XFF);
    }
}

//设置LCD的自动扫描方向
//dir:0~7,代表8个方向(具体定义见lcd.h)
//9341/5310/5510/1963/7789等IC已经实际测试
//注意:其他函数可能会受到此函数设置的影响(尤其是9341),
//所以,一般设置为L2R_U2D即可,如果设置为其他扫描方式,可能导致显示不正常.
void LCD_Scan_Dir(u8 dir)
{
    u16 regval = 0;
    u16 dirreg = 0;
    u16 temp;

    //横屏时，对1963不改变扫描方向, 其他IC改变扫描方向！竖屏时1963改变方向, 其他IC不改变扫描方向
    if ((lcddev.dir == 1 && lcddev.id != 0X1963) || (lcddev.dir == 0 && lcddev.id == 0X1963))
    {
        switch (dir)   //方向转换
        {
            case 0:
                dir = 6;
                break;

            case 1:
                dir = 7;
                break;

            case 2:
                dir = 4;
                break;

            case 3:
                dir = 5;
                break;

            case 4:
                dir = 1;
                break;

            case 5:
                dir = 0;
                break;

            case 6:
                dir = 3;
                break;

            case 7:
                dir = 2;
                break;
        }
    }

    switch (dir)
    {
        case L2R_U2D://从左到右,从上到下
            regval |= (0 << 7) | (0 << 6) | (0 << 5);
            break;

        case L2R_D2U://从左到右,从下到上
            regval |= (1 << 7) | (0 << 6) | (0 << 5);
            break;

        case R2L_U2D://从右到左,从上到下
            regval |= (0 << 7) | (1 << 6) | (0 << 5);
            break;

        case R2L_D2U://从右到左,从下到上
            regval |= (1 << 7) | (1 << 6) | (0 << 5);
            break;

        case U2D_L2R://从上到下,从左到右
            regval |= (0 << 7) | (0 << 6) | (1 << 5);
            break;

        case U2D_R2L://从上到下,从右到左
            regval |= (0 << 7) | (1 << 6) | (1 << 5);
            break;

        case D2U_L2R://从下到上,从左到右
            regval |= (1 << 7) | (0 << 6) | (1 << 5);
            break;

        case D2U_R2L://从下到上,从右到左
            regval |= (1 << 7) | (1 << 6) | (1 << 5);
            break;
    }

    if (lcddev.id == 0X5510)dirreg = 0X3600;
    else dirreg = 0X36;

    if (lcddev.id == 0X9341 || lcddev.id == 0X7789)   //9341 & 7789 要设置BGR位
    {
        regval |= 0X08;
    }

    LCD_WriteReg(dirreg, regval);

    if (lcddev.id != 0X1963)   //1963不做坐标处理
    {
        if (regval & 0X20)
        {
            if (lcddev.width < lcddev.height)   //交换X,Y
            {
                temp = lcddev.width;
                lcddev.width = lcddev.height;
                lcddev.height = temp;
            }
        }
        else
        {
            if (lcddev.width > lcddev.height)   //交换X,Y
            {
                temp = lcddev.width;
                lcddev.width = lcddev.height;
                lcddev.height = temp;
            }
        }
    }

    //设置显示区域(开窗)大小
    if (lcddev.id == 0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(0);
        LCD_WR_REG(lcddev.setxcmd + 1);
        LCD_WR_DATA(0);
        LCD_WR_REG(lcddev.setxcmd + 2);
        LCD_WR_DATA((lcddev.width - 1) >> 8);
        LCD_WR_REG(lcddev.setxcmd + 3);
        LCD_WR_DATA((lcddev.width - 1) & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(0);
        LCD_WR_REG(lcddev.setycmd + 1);
        LCD_WR_DATA(0);
        LCD_WR_REG(lcddev.setycmd + 2);
        LCD_WR_DATA((lcddev.height - 1) >> 8);
        LCD_WR_REG(lcddev.setycmd + 3);
        LCD_WR_DATA((lcddev.height - 1) & 0XFF);
    }
    else
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(0);
        LCD_WR_DATA(0);
        LCD_WR_DATA((lcddev.width - 1) >> 8);
        LCD_WR_DATA((lcddev.width - 1) & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(0);
        LCD_WR_DATA(0);
        LCD_WR_DATA((lcddev.height - 1) >> 8);
        LCD_WR_DATA((lcddev.height - 1) & 0XFF);
    }
}

//画点
//x,y:坐标
//POINT_COLOR:此点的颜色
void LCD_DrawPoint(u16 x,u16 y)
{
    LCD_SetCursor(x, y);        //设置光标位置
    LCD_WriteRAM_Prepare();     //开始写入GRAM
    LCD_WR_DATA(POINT_COLOR);
}

//快速画点
//x,y:坐标
//color:颜色
void LCD_Fast_DrawPoint(u16 x,u16 y,u16 color)
{
    if (lcddev.id == 0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(x >> 8);
        LCD_WR_REG(lcddev.setxcmd + 1);
        LCD_WR_DATA(x & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(y >> 8);
        LCD_WR_REG(lcddev.setycmd + 1);
        LCD_WR_DATA(y & 0XFF);
    }
    else if (lcddev.id == 0X1963)
    {
        if (lcddev.dir == 0)x = lcddev.width - 1 - x;

        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(x >> 8);
        LCD_WR_DATA(x & 0XFF);
        LCD_WR_DATA(x >> 8);
        LCD_WR_DATA(x & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(y >> 8);
        LCD_WR_DATA(y & 0XFF);
        LCD_WR_DATA(y >> 8);
        LCD_WR_DATA(y & 0XFF);
    }
    else     //9341/5310/7789等设置坐标
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(x >> 8);
        LCD_WR_DATA(x & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(y >> 8);
        LCD_WR_DATA(y & 0XFF);
    }

    LCD_RS_CLR;
    LCD_CS_CLR;
    DATAOUT(lcddev.wramcmd);    //写指令
    LCD_WR_CLR;
    LCD_WR_SET;
    LCD_CS_SET;
    LCD_WR_DATA(color);         //写数据
}

//SSD1963 背光设置
//pwm:背光等级,0~100.越大越亮.
void LCD_SSD_BackLightSet(u8 pwm)
{
    LCD_WR_REG(0xBE);           //配置PWM输出
    LCD_WR_DATA(0x05);          //1设置PWM频率
    LCD_WR_DATA(pwm * 2.55);    //2设置PWM占空比
    LCD_WR_DATA(0x01);          //3设置C
    LCD_WR_DATA(0xFF);          //4设置D
    LCD_WR_DATA(0x00);          //5设置E
    LCD_WR_DATA(0x00);          //6设置F
}

//设置LCD显示方向
//dir:0,竖屏；1,横屏
void LCD_Display_Dir(u8 dir)
{
    lcddev.dir = dir;       //竖屏/横屏

    if (dir == 0)           //竖屏
    {
        lcddev.width = 240;
        lcddev.height = 320;

        if (lcddev.id == 0x5510)
        {
            lcddev.wramcmd = 0X2C00;
            lcddev.setxcmd = 0X2A00;
            lcddev.setycmd = 0X2B00;
            lcddev.width = 480;
            lcddev.height = 800;
        }
        else if (lcddev.id == 0X1963)
        {
            lcddev.wramcmd = 0X2C;  //设置写入GRAM的指令
            lcddev.setxcmd = 0X2B;  //设置写X坐标指令
            lcddev.setycmd = 0X2A;  //设置写Y坐标指令
            lcddev.width = 480;     //设置宽度480
            lcddev.height = 800;    //设置高度800
        }
        else                        //其他IC, 包括: 9341 / 5310 / 7789等IC
        {
            lcddev.wramcmd = 0X2C;
            lcddev.setxcmd = 0X2A;
            lcddev.setycmd = 0X2B;
        }

        if (lcddev.id == 0X5310)    //如果是5310 则表示是 320*480分辨率
        {
            lcddev.width = 320;
            lcddev.height = 480;
        }
    }
    else     //横屏
    {
        lcddev.width = 320;
        lcddev.height = 240;

        if (lcddev.id == 0x5510)
        {
            lcddev.wramcmd = 0X2C00;
            lcddev.setxcmd = 0X2A00;
            lcddev.setycmd = 0X2B00;
            lcddev.width = 800;
            lcddev.height = 480;
        }
        else if (lcddev.id == 0X1963)
        {
            lcddev.wramcmd = 0X2C;  //设置写入GRAM的指令
            lcddev.setxcmd = 0X2A;  //设置写X坐标指令
            lcddev.setycmd = 0X2B;  //设置写Y坐标指令
            lcddev.width = 800;     //设置宽度800
            lcddev.height = 480;    //设置高度480
        }
        else                        //其他IC, 包括: 9341 / 5310 / 7789等IC
        {
            lcddev.wramcmd = 0X2C;
            lcddev.setxcmd = 0X2A;
            lcddev.setycmd = 0X2B;
        }

        if (lcddev.id == 0X5310)    //如果是5310 则表示是 320*480分辨率
        {
            lcddev.width = 480;
            lcddev.height = 320;
        }
    }

    LCD_Scan_Dir(DFT_SCAN_DIR);     //默认扫描方向
}

//设置窗口,并自动设置画点坐标到窗口左上角(sx,sy).
//sx,sy:窗口起始坐标(左上角)
//width,height:窗口宽度和高度,必须大于0!!
//窗体大小:width*height. 
void LCD_Set_Window(u16 sx,u16 sy,u16 width,u16 height)
{    
    u16 twidth, theight;
    twidth = sx + width - 1;
    theight = sy + height - 1;

    if (lcddev.id == 0X1963 && lcddev.dir != 1)     //1963竖屏特殊处理
    {
        sx = lcddev.width - width - sx;
        height = sy + height - 1;
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(sx >> 8);
        LCD_WR_DATA(sx & 0XFF);
        LCD_WR_DATA((sx + width - 1) >> 8);
        LCD_WR_DATA((sx + width - 1) & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(sy >> 8);
        LCD_WR_DATA(sy & 0XFF);
        LCD_WR_DATA(height >> 8);
        LCD_WR_DATA(height & 0XFF);
    }
    else if (lcddev.id == 0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(sx >> 8);
        LCD_WR_REG(lcddev.setxcmd + 1);
        LCD_WR_DATA(sx & 0XFF);
        LCD_WR_REG(lcddev.setxcmd + 2);
        LCD_WR_DATA(twidth >> 8);
        LCD_WR_REG(lcddev.setxcmd + 3);
        LCD_WR_DATA(twidth & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(sy >> 8);
        LCD_WR_REG(lcddev.setycmd + 1);
        LCD_WR_DATA(sy & 0XFF);
        LCD_WR_REG(lcddev.setycmd + 2);
        LCD_WR_DATA(theight >> 8);
        LCD_WR_REG(lcddev.setycmd + 3);
        LCD_WR_DATA(theight & 0XFF);
    }
    else     //9341/5310/7789/1963横屏 等 设置窗口
    {
        LCD_WR_REG(lcddev.setxcmd);
        LCD_WR_DATA(sx >> 8);
        LCD_WR_DATA(sx & 0XFF);
        LCD_WR_DATA(twidth >> 8);
        LCD_WR_DATA(twidth & 0XFF);
        LCD_WR_REG(lcddev.setycmd);
        LCD_WR_DATA(sy >> 8);
        LCD_WR_DATA(sy & 0XFF);
        LCD_WR_DATA(theight >> 8);
        LCD_WR_DATA(theight & 0XFF);
    }
}

//初始化lcd
//该初始化函数可以初始化各种ALIENTEK出品的LCD液晶屏
//本函数占用较大flash,用户可以根据自己的实际情况,删掉未用到的LCD初始化代码.以节省空间.
void LCD_Init(void)
{
    GPIO_InitTypeDef GPIO_Initure;

    __HAL_RCC_GPIOB_CLK_ENABLE();           	//开启GPIOB时钟
    __HAL_RCC_GPIOC_CLK_ENABLE();           	//开启GPIOC时钟

    //PC6,7,8,9,10
    GPIO_Initure.Pin=GPIO_PIN_6|GPIO_PIN_7|GPIO_PIN_8|\
                     GPIO_PIN_9|GPIO_PIN_10; 				
    GPIO_Initure.Mode=GPIO_MODE_OUTPUT_PP;  	//推挽输出
    GPIO_Initure.Pull=GPIO_PULLUP;          	//上拉
    GPIO_Initure.Speed=GPIO_SPEED_FREQ_HIGH;    //高速
    HAL_GPIO_Init(GPIOC,&GPIO_Initure);

    //PB0~15
    GPIO_Initure.Pin=GPIO_PIN_All;				//PB推挽输出
    HAL_GPIO_Init(GPIOB,&GPIO_Initure);
        
    __HAL_AFIO_REMAP_SWJ_DISABLE();				//禁止JTAG

    delay_ms(50); // delay 50 ms 
    LCD_WriteReg(0x0000,0x0001);
    delay_ms(50); // delay 50 ms 
    
    
    //尝试9341 ID的读取
    LCD_WR_REG(0XD3);
    lcddev.id = LCD_RD_DATA();          //dummy read
    lcddev.id = LCD_RD_DATA();          //读到0X00
    lcddev.id = LCD_RD_DATA();          //读取0X93
    lcddev.id <<= 8;
    lcddev.id |= LCD_RD_DATA();         //读取0X41

    if (lcddev.id != 0X9341)            //不是 9341 , 尝试看看是不是 ST7789
    {
        LCD_WR_REG(0X04);
        lcddev.id = LCD_RD_DATA();      //dummy read
        lcddev.id = LCD_RD_DATA();      //读到0X85
        lcddev.id = LCD_RD_DATA();      //读取0X85
        lcddev.id <<= 8;
        lcddev.id |= LCD_RD_DATA();     //读取0X52

        if (lcddev.id == 0X8552)        //将8552的ID转换成7789
        {
            lcddev.id = 0x7789;
        }

        if (lcddev.id != 0x7789)        //也不是ST7789, 尝试是不是 NT35310
        {
            LCD_WR_REG(0XD4);
            lcddev.id = LCD_RD_DATA();  //dummy read
            lcddev.id = LCD_RD_DATA();  //读回0X01
            lcddev.id = LCD_RD_DATA();  //读回0X53
            lcddev.id <<= 8;
            lcddev.id |= LCD_RD_DATA(); //这里读回0X10

            if (lcddev.id != 0X5310)    //也不是NT35310,尝试看看是不是NT35510
            {
                //发送秘钥（厂家提供,照搬即可）
                LCD_WriteReg(0xF000, 0x0055);
                LCD_WriteReg(0xF001, 0x00AA);
                LCD_WriteReg(0xF002, 0x0052);
                LCD_WriteReg(0xF003, 0x0008);
                LCD_WriteReg(0xF004, 0x0001);

                LCD_WR_REG(0xC500);             //读取ID高8位
                lcddev.id = LCD_RD_DATA();      //读回0X55
                lcddev.id <<= 8;

                LCD_WR_REG(0xC501);             //读取ID低8位
                lcddev.id |= LCD_RD_DATA();     //读回0X10
                delay_ms(5);
                
                if (lcddev.id != 0X5510)        //也不是NT5510,尝试看看是不是SSD1963
                {
                    LCD_WR_REG(0XA1);
                    lcddev.id = LCD_RD_DATA();
                    lcddev.id = LCD_RD_DATA();  //读回0X57
                    lcddev.id <<= 8;
                    lcddev.id |= LCD_RD_DATA(); //读回0X61

                    if (lcddev.id == 0X5761)lcddev.id = 0X1963; //SSD1963读回的ID是5761H,为方便区分,我们强制设置为1963
                }
            }
        }
    }

 //   printf(" LCD ID:%x\r\n", lcddev.id); //打印LCD ID

    if (lcddev.id == 0X9341)    //9341初始化
    {
        LCD_WR_REG(0xCF);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC1);
        LCD_WR_DATAX(0X30);
        LCD_WR_REG(0xED);
        LCD_WR_DATAX(0x64);
        LCD_WR_DATAX(0x03);
        LCD_WR_DATAX(0X12);
        LCD_WR_DATAX(0X81);
        LCD_WR_REG(0xE8);
        LCD_WR_DATAX(0x85);
        LCD_WR_DATAX(0x10);
        LCD_WR_DATAX(0x7A);
        LCD_WR_REG(0xCB);
        LCD_WR_DATAX(0x39);
        LCD_WR_DATAX(0x2C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x34);
        LCD_WR_DATAX(0x02);
        LCD_WR_REG(0xF7);
        LCD_WR_DATAX(0x20);
        LCD_WR_REG(0xEA);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_REG(0xC0);       //Power control
        LCD_WR_DATAX(0x1B);     //VRH[5:0]
        LCD_WR_REG(0xC1);       //Power control
        LCD_WR_DATAX(0x01);     //SAP[2:0];BT[3:0]
        LCD_WR_REG(0xC5);       //VCM control
        LCD_WR_DATAX(0x30);     //3F
        LCD_WR_DATAX(0x30);     //3C
        LCD_WR_REG(0xC7);       //VCM control2
        LCD_WR_DATAX(0XB7);
        LCD_WR_REG(0x36);       // Memory Access Control
        LCD_WR_DATAX(0x48);
        LCD_WR_REG(0x3A);
        LCD_WR_DATAX(0x55);
        LCD_WR_REG(0xB1);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x1A);
        LCD_WR_REG(0xB6);       // Display Function Control
        LCD_WR_DATAX(0x0A);
        LCD_WR_DATAX(0xA2);
        LCD_WR_REG(0xF2);       // 3Gamma Function Disable
        LCD_WR_DATAX(0x00);
        LCD_WR_REG(0x26);       //Gamma curve selected
        LCD_WR_DATAX(0x01);
        LCD_WR_REG(0xE0);       //Set Gamma
        LCD_WR_DATAX(0x0F);
        LCD_WR_DATAX(0x2A);
        LCD_WR_DATAX(0x28);
        LCD_WR_DATAX(0x08);
        LCD_WR_DATAX(0x0E);
        LCD_WR_DATAX(0x08);
        LCD_WR_DATAX(0x54);
        LCD_WR_DATAX(0XA9);
        LCD_WR_DATAX(0x43);
        LCD_WR_DATAX(0x0A);
        LCD_WR_DATAX(0x0F);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_REG(0XE1);       //Set Gamma
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x15);
        LCD_WR_DATAX(0x17);
        LCD_WR_DATAX(0x07);
        LCD_WR_DATAX(0x11);
        LCD_WR_DATAX(0x06);
        LCD_WR_DATAX(0x2B);
        LCD_WR_DATAX(0x56);
        LCD_WR_DATAX(0x3C);
        LCD_WR_DATAX(0x05);
        LCD_WR_DATAX(0x10);
        LCD_WR_DATAX(0x0F);
        LCD_WR_DATAX(0x3F);
        LCD_WR_DATAX(0x3F);
        LCD_WR_DATAX(0x0F);
        LCD_WR_REG(0x2B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x01);
        LCD_WR_DATAX(0x3f);
        LCD_WR_REG(0x2A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xef);
        LCD_WR_REG(0x11);       //Exit Sleep
        delay_ms(120);
        LCD_WR_REG(0x29);       //display on
    }
    else if (lcddev.id == 0x7789)     //7789初始化
    {
        LCD_WR_REG(0x11);

        delay_ms(120);

        LCD_WR_REG(0x36);
        LCD_WR_DATAX(0x00);


        LCD_WR_REG(0x3A);
        LCD_WR_DATAX(0X05);

        LCD_WR_REG(0xB2);
        LCD_WR_DATAX(0x0C);
        LCD_WR_DATAX(0x0C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x33);
        LCD_WR_DATAX(0x33);

        LCD_WR_REG(0xB7);
        LCD_WR_DATAX(0x35);

        LCD_WR_REG(0xBB);       //vcom
        LCD_WR_DATAX(0x32);     //30

        LCD_WR_REG(0xC0);
        LCD_WR_DATAX(0x0C);

        LCD_WR_REG(0xC2);
        LCD_WR_DATAX(0x01);

        LCD_WR_REG(0xC3);       //vrh
        LCD_WR_DATAX(0x10);     //17 0D

        LCD_WR_REG(0xC4);       //vdv
        LCD_WR_DATAX(0x20);     //20

        LCD_WR_REG(0xC6);
        LCD_WR_DATAX(0x0f);

        LCD_WR_REG(0xD0);
        LCD_WR_DATAX(0xA4);
        LCD_WR_DATAX(0xA1);

        LCD_WR_REG(0xE0);       //Set Gamma
        LCD_WR_DATAX(0xd0);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x02);
        LCD_WR_DATAX(0x07);
        LCD_WR_DATAX(0x0a);
        LCD_WR_DATAX(0x28);
        LCD_WR_DATAX(0x32);
        LCD_WR_DATAX(0X44);
        LCD_WR_DATAX(0x42);
        LCD_WR_DATAX(0x06);
        LCD_WR_DATAX(0x0e);
        LCD_WR_DATAX(0x12);
        LCD_WR_DATAX(0x14);
        LCD_WR_DATAX(0x17);


        LCD_WR_REG(0XE1);       //Set Gamma
        LCD_WR_DATAX(0xd0);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x02);
        LCD_WR_DATAX(0x07);
        LCD_WR_DATAX(0x0a);
        LCD_WR_DATAX(0x28);
        LCD_WR_DATAX(0x31);
        LCD_WR_DATAX(0x54);
        LCD_WR_DATAX(0x47);
        LCD_WR_DATAX(0x0e);
        LCD_WR_DATAX(0x1c);
        LCD_WR_DATAX(0x17);
        LCD_WR_DATAX(0x1b);
        LCD_WR_DATAX(0x1e);


        LCD_WR_REG(0x2A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xef);

        LCD_WR_REG(0x2B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x01);
        LCD_WR_DATAX(0x3f);

        LCD_WR_REG(0x29);       //display on
    }
    else if (lcddev.id == 0x5310)
    {
        LCD_WR_REG(0xED);
        LCD_WR_DATAX(0x01);
        LCD_WR_DATAX(0xFE);

        LCD_WR_REG(0xEE);
        LCD_WR_DATAX(0xDE);
        LCD_WR_DATAX(0x21);

        LCD_WR_REG(0xF1);
        LCD_WR_DATAX(0x01);
        LCD_WR_REG(0xDF);
        LCD_WR_DATAX(0x10);

        //VCOMvoltage//
        LCD_WR_REG(0xC4);
        LCD_WR_DATAX(0x8F);	  //5f

        LCD_WR_REG(0xC6);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xE2);
        LCD_WR_DATAX(0xE2);
        LCD_WR_DATAX(0xE2);
        LCD_WR_REG(0xBF);
        LCD_WR_DATAX(0xAA);

        LCD_WR_REG(0xB0);
        LCD_WR_DATAX(0x0D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x0D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x11);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x19);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x21);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x2D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x5D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x5D);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB1);
        LCD_WR_DATAX(0x80);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x8B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x96);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x02);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x03);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB3);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB4);
        LCD_WR_DATAX(0x8B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x96);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA1);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB5);
        LCD_WR_DATAX(0x02);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x03);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x04);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB6);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB7);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3F);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x5E);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x64);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x8C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xAC);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xDC);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x70);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x90);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xEB);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xDC);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xB8);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xBA);
        LCD_WR_DATAX(0x24);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC1);
        LCD_WR_DATAX(0x20);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x54);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xFF);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC2);
        LCD_WR_DATAX(0x0A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x04);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC3);
        LCD_WR_DATAX(0x3C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x39);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x37);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x36);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x32);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x2F);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x2C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x29);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x26);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x24);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x24);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x23);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x36);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x32);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x2F);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x2C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x29);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x26);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x24);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x24);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x23);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC4);
        LCD_WR_DATAX(0x62);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x05);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x84);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF0);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x18);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA4);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x18);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x50);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x0C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x17);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x95);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xE6);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC5);
        LCD_WR_DATAX(0x32);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x65);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x76);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x88);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC6);
        LCD_WR_DATAX(0x20);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x17);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x01);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC7);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC8);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xC9);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE0);
        LCD_WR_DATAX(0x16);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x1C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x21);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x36);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x46);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x52);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x64);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x7A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x8B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA8);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xB9);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC4);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xCA);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD9);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xE0);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE1);
        LCD_WR_DATAX(0x16);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x1C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x22);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x36);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x45);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x52);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x64);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x7A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x8B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA8);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xB9);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC4);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xCA);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD8);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xE0);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE2);
        LCD_WR_DATAX(0x05);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x0B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x1B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x34);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x4F);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x61);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x79);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x88);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x97);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA6);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xB7);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC7);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD1);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD6);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xDD);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);
        LCD_WR_REG(0xE3);
        LCD_WR_DATAX(0x05);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x1C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x33);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x50);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x62);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x78);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x88);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x97);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA6);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xB7);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC7);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD1);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD5);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xDD);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE4);
        LCD_WR_DATAX(0x01);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x01);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x02);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x2A);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x4B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x5D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x74);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x84);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x93);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xB3);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xBE);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC4);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xCD);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD3);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xDD);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);
        LCD_WR_REG(0xE5);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x02);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x29);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x3C);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x4B);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x5D);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x74);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x84);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x93);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xA2);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xB3);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xBE);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xC4);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xCD);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xD3);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xDC);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xF3);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE6);
        LCD_WR_DATAX(0x11);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x34);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x56);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x76);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x77);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x66);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x88);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xBB);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x66);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x55);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x55);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x45);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x43);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE7);
        LCD_WR_DATAX(0x32);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x55);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x76);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x66);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x67);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x67);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x87);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xBB);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x77);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x56);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x23);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x33);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x45);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE8);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x87);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x88);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x77);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x66);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x88);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xAA);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0xBB);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x99);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x66);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x55);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x55);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x44);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x55);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xE9);
        LCD_WR_DATAX(0xAA);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0x00);
        LCD_WR_DATAX(0xAA);

        LCD_WR_REG(0xCF);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xF0);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x50);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xF3);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0xF9);
        LCD_WR_DATAX(0x06);
        LCD_WR_DATAX(0x10);
        LCD_WR_DATAX(0x29);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0x3A);
        LCD_WR_DATAX(0x55);	//66

        LCD_WR_REG(0x11);
        delay_ms(100);
        LCD_WR_REG(0x29);
        LCD_WR_REG(0x35);
        LCD_WR_DATAX(0x00);

        LCD_WR_REG(0x51);
        LCD_WR_DATAX(0xFF);
        LCD_WR_REG(0x53);
        LCD_WR_DATAX(0x2C);
        LCD_WR_REG(0x55);
        LCD_WR_DATAX(0x82);
        LCD_WR_REG(0x2c);
    }
    else if (lcddev.id == 0x5510)
    {
        LCD_WriteReg(0xF000, 0x55);
        LCD_WriteReg(0xF001, 0xAA);
        LCD_WriteReg(0xF002, 0x52);
        LCD_WriteReg(0xF003, 0x08);
        LCD_WriteReg(0xF004, 0x01);
        //AVDD Set AVDD 5.2V
        LCD_WriteReg(0xB000, 0x0D);
        LCD_WriteReg(0xB001, 0x0D);
        LCD_WriteReg(0xB002, 0x0D);
        //AVDD ratio
        LCD_WriteReg(0xB600, 0x34);
        LCD_WriteReg(0xB601, 0x34);
        LCD_WriteReg(0xB602, 0x34);
        //AVEE -5.2V
        LCD_WriteReg(0xB100, 0x0D);
        LCD_WriteReg(0xB101, 0x0D);
        LCD_WriteReg(0xB102, 0x0D);
        //AVEE ratio
        LCD_WriteReg(0xB700, 0x34);
        LCD_WriteReg(0xB701, 0x34);
        LCD_WriteReg(0xB702, 0x34);
        //VCL -2.5V
        LCD_WriteReg(0xB200, 0x00);
        LCD_WriteReg(0xB201, 0x00);
        LCD_WriteReg(0xB202, 0x00);
        //VCL ratio
        LCD_WriteReg(0xB800, 0x24);
        LCD_WriteReg(0xB801, 0x24);
        LCD_WriteReg(0xB802, 0x24);
        //VGH 15V (Free pump)
        LCD_WriteReg(0xBF00, 0x01);
        LCD_WriteReg(0xB300, 0x0F);
        LCD_WriteReg(0xB301, 0x0F);
        LCD_WriteReg(0xB302, 0x0F);
        //VGH ratio
        LCD_WriteReg(0xB900, 0x34);
        LCD_WriteReg(0xB901, 0x34);
        LCD_WriteReg(0xB902, 0x34);
        //VGL_REG -10V
        LCD_WriteReg(0xB500, 0x08);
        LCD_WriteReg(0xB501, 0x08);
        LCD_WriteReg(0xB502, 0x08);
        LCD_WriteReg(0xC200, 0x03);
        //VGLX ratio
        LCD_WriteReg(0xBA00, 0x24);
        LCD_WriteReg(0xBA01, 0x24);
        LCD_WriteReg(0xBA02, 0x24);
        //VGMP/VGSP 4.5V/0V
        LCD_WriteReg(0xBC00, 0x00);
        LCD_WriteReg(0xBC01, 0x78);
        LCD_WriteReg(0xBC02, 0x00);
        //VGMN/VGSN -4.5V/0V
        LCD_WriteReg(0xBD00, 0x00);
        LCD_WriteReg(0xBD01, 0x78);
        LCD_WriteReg(0xBD02, 0x00);
        //VCOM
        LCD_WriteReg(0xBE00, 0x00);
        LCD_WriteReg(0xBE01, 0x64);
        //Gamma Setting
        LCD_WriteReg(0xD100, 0x00);
        LCD_WriteReg(0xD101, 0x33);
        LCD_WriteReg(0xD102, 0x00);
        LCD_WriteReg(0xD103, 0x34);
        LCD_WriteReg(0xD104, 0x00);
        LCD_WriteReg(0xD105, 0x3A);
        LCD_WriteReg(0xD106, 0x00);
        LCD_WriteReg(0xD107, 0x4A);
        LCD_WriteReg(0xD108, 0x00);
        LCD_WriteReg(0xD109, 0x5C);
        LCD_WriteReg(0xD10A, 0x00);
        LCD_WriteReg(0xD10B, 0x81);
        LCD_WriteReg(0xD10C, 0x00);
        LCD_WriteReg(0xD10D, 0xA6);
        LCD_WriteReg(0xD10E, 0x00);
        LCD_WriteReg(0xD10F, 0xE5);
        LCD_WriteReg(0xD110, 0x01);
        LCD_WriteReg(0xD111, 0x13);
        LCD_WriteReg(0xD112, 0x01);
        LCD_WriteReg(0xD113, 0x54);
        LCD_WriteReg(0xD114, 0x01);
        LCD_WriteReg(0xD115, 0x82);
        LCD_WriteReg(0xD116, 0x01);
        LCD_WriteReg(0xD117, 0xCA);
        LCD_WriteReg(0xD118, 0x02);
        LCD_WriteReg(0xD119, 0x00);
        LCD_WriteReg(0xD11A, 0x02);
        LCD_WriteReg(0xD11B, 0x01);
        LCD_WriteReg(0xD11C, 0x02);
        LCD_WriteReg(0xD11D, 0x34);
        LCD_WriteReg(0xD11E, 0x02);
        LCD_WriteReg(0xD11F, 0x67);
        LCD_WriteReg(0xD120, 0x02);
        LCD_WriteReg(0xD121, 0x84);
        LCD_WriteReg(0xD122, 0x02);
        LCD_WriteReg(0xD123, 0xA4);
        LCD_WriteReg(0xD124, 0x02);
        LCD_WriteReg(0xD125, 0xB7);
        LCD_WriteReg(0xD126, 0x02);
        LCD_WriteReg(0xD127, 0xCF);
        LCD_WriteReg(0xD128, 0x02);
        LCD_WriteReg(0xD129, 0xDE);
        LCD_WriteReg(0xD12A, 0x02);
        LCD_WriteReg(0xD12B, 0xF2);
        LCD_WriteReg(0xD12C, 0x02);
        LCD_WriteReg(0xD12D, 0xFE);
        LCD_WriteReg(0xD12E, 0x03);
        LCD_WriteReg(0xD12F, 0x10);
        LCD_WriteReg(0xD130, 0x03);
        LCD_WriteReg(0xD131, 0x33);
        LCD_WriteReg(0xD132, 0x03);
        LCD_WriteReg(0xD133, 0x6D);
        LCD_WriteReg(0xD200, 0x00);
        LCD_WriteReg(0xD201, 0x33);
        LCD_WriteReg(0xD202, 0x00);
        LCD_WriteReg(0xD203, 0x34);
        LCD_WriteReg(0xD204, 0x00);
        LCD_WriteReg(0xD205, 0x3A);
        LCD_WriteReg(0xD206, 0x00);
        LCD_WriteReg(0xD207, 0x4A);
        LCD_WriteReg(0xD208, 0x00);
        LCD_WriteReg(0xD209, 0x5C);
        LCD_WriteReg(0xD20A, 0x00);

        LCD_WriteReg(0xD20B, 0x81);
        LCD_WriteReg(0xD20C, 0x00);
        LCD_WriteReg(0xD20D, 0xA6);
        LCD_WriteReg(0xD20E, 0x00);
        LCD_WriteReg(0xD20F, 0xE5);
        LCD_WriteReg(0xD210, 0x01);
        LCD_WriteReg(0xD211, 0x13);
        LCD_WriteReg(0xD212, 0x01);
        LCD_WriteReg(0xD213, 0x54);
        LCD_WriteReg(0xD214, 0x01);
        LCD_WriteReg(0xD215, 0x82);
        LCD_WriteReg(0xD216, 0x01);
        LCD_WriteReg(0xD217, 0xCA);
        LCD_WriteReg(0xD218, 0x02);
        LCD_WriteReg(0xD219, 0x00);
        LCD_WriteReg(0xD21A, 0x02);
        LCD_WriteReg(0xD21B, 0x01);
        LCD_WriteReg(0xD21C, 0x02);
        LCD_WriteReg(0xD21D, 0x34);
        LCD_WriteReg(0xD21E, 0x02);
        LCD_WriteReg(0xD21F, 0x67);
        LCD_WriteReg(0xD220, 0x02);
        LCD_WriteReg(0xD221, 0x84);
        LCD_WriteReg(0xD222, 0x02);
        LCD_WriteReg(0xD223, 0xA4);
        LCD_WriteReg(0xD224, 0x02);
        LCD_WriteReg(0xD225, 0xB7);
        LCD_WriteReg(0xD226, 0x02);
        LCD_WriteReg(0xD227, 0xCF);
        LCD_WriteReg(0xD228, 0x02);
        LCD_WriteReg(0xD229, 0xDE);
        LCD_WriteReg(0xD22A, 0x02);
        LCD_WriteReg(0xD22B, 0xF2);
        LCD_WriteReg(0xD22C, 0x02);
        LCD_WriteReg(0xD22D, 0xFE);
        LCD_WriteReg(0xD22E, 0x03);
        LCD_WriteReg(0xD22F, 0x10);
        LCD_WriteReg(0xD230, 0x03);
        LCD_WriteReg(0xD231, 0x33);
        LCD_WriteReg(0xD232, 0x03);
        LCD_WriteReg(0xD233, 0x6D);
        LCD_WriteReg(0xD300, 0x00);
        LCD_WriteReg(0xD301, 0x33);
        LCD_WriteReg(0xD302, 0x00);
        LCD_WriteReg(0xD303, 0x34);
        LCD_WriteReg(0xD304, 0x00);
        LCD_WriteReg(0xD305, 0x3A);
        LCD_WriteReg(0xD306, 0x00);
        LCD_WriteReg(0xD307, 0x4A);
        LCD_WriteReg(0xD308, 0x00);
        LCD_WriteReg(0xD309, 0x5C);
        LCD_WriteReg(0xD30A, 0x00);

        LCD_WriteReg(0xD30B, 0x81);
        LCD_WriteReg(0xD30C, 0x00);
        LCD_WriteReg(0xD30D, 0xA6);
        LCD_WriteReg(0xD30E, 0x00);
        LCD_WriteReg(0xD30F, 0xE5);
        LCD_WriteReg(0xD310, 0x01);
        LCD_WriteReg(0xD311, 0x13);
        LCD_WriteReg(0xD312, 0x01);
        LCD_WriteReg(0xD313, 0x54);
        LCD_WriteReg(0xD314, 0x01);
        LCD_WriteReg(0xD315, 0x82);
        LCD_WriteReg(0xD316, 0x01);
        LCD_WriteReg(0xD317, 0xCA);
        LCD_WriteReg(0xD318, 0x02);
        LCD_WriteReg(0xD319, 0x00);
        LCD_WriteReg(0xD31A, 0x02);
        LCD_WriteReg(0xD31B, 0x01);
        LCD_WriteReg(0xD31C, 0x02);
        LCD_WriteReg(0xD31D, 0x34);
        LCD_WriteReg(0xD31E, 0x02);
        LCD_WriteReg(0xD31F, 0x67);
        LCD_WriteReg(0xD320, 0x02);
        LCD_WriteReg(0xD321, 0x84);
        LCD_WriteReg(0xD322, 0x02);
        LCD_WriteReg(0xD323, 0xA4);
        LCD_WriteReg(0xD324, 0x02);
        LCD_WriteReg(0xD325, 0xB7);
        LCD_WriteReg(0xD326, 0x02);
        LCD_WriteReg(0xD327, 0xCF);
        LCD_WriteReg(0xD328, 0x02);
        LCD_WriteReg(0xD329, 0xDE);
        LCD_WriteReg(0xD32A, 0x02);
        LCD_WriteReg(0xD32B, 0xF2);
        LCD_WriteReg(0xD32C, 0x02);
        LCD_WriteReg(0xD32D, 0xFE);
        LCD_WriteReg(0xD32E, 0x03);
        LCD_WriteReg(0xD32F, 0x10);
        LCD_WriteReg(0xD330, 0x03);
        LCD_WriteReg(0xD331, 0x33);
        LCD_WriteReg(0xD332, 0x03);
        LCD_WriteReg(0xD333, 0x6D);
        LCD_WriteReg(0xD400, 0x00);
        LCD_WriteReg(0xD401, 0x33);
        LCD_WriteReg(0xD402, 0x00);
        LCD_WriteReg(0xD403, 0x34);
        LCD_WriteReg(0xD404, 0x00);
        LCD_WriteReg(0xD405, 0x3A);
        LCD_WriteReg(0xD406, 0x00);
        LCD_WriteReg(0xD407, 0x4A);
        LCD_WriteReg(0xD408, 0x00);
        LCD_WriteReg(0xD409, 0x5C);
        LCD_WriteReg(0xD40A, 0x00);
        LCD_WriteReg(0xD40B, 0x81);

        LCD_WriteReg(0xD40C, 0x00);
        LCD_WriteReg(0xD40D, 0xA6);
        LCD_WriteReg(0xD40E, 0x00);
        LCD_WriteReg(0xD40F, 0xE5);
        LCD_WriteReg(0xD410, 0x01);
        LCD_WriteReg(0xD411, 0x13);
        LCD_WriteReg(0xD412, 0x01);
        LCD_WriteReg(0xD413, 0x54);
        LCD_WriteReg(0xD414, 0x01);
        LCD_WriteReg(0xD415, 0x82);
        LCD_WriteReg(0xD416, 0x01);
        LCD_WriteReg(0xD417, 0xCA);
        LCD_WriteReg(0xD418, 0x02);
        LCD_WriteReg(0xD419, 0x00);
        LCD_WriteReg(0xD41A, 0x02);
        LCD_WriteReg(0xD41B, 0x01);
        LCD_WriteReg(0xD41C, 0x02);
        LCD_WriteReg(0xD41D, 0x34);
        LCD_WriteReg(0xD41E, 0x02);
        LCD_WriteReg(0xD41F, 0x67);
        LCD_WriteReg(0xD420, 0x02);
        LCD_WriteReg(0xD421, 0x84);
        LCD_WriteReg(0xD422, 0x02);
        LCD_WriteReg(0xD423, 0xA4);
        LCD_WriteReg(0xD424, 0x02);
        LCD_WriteReg(0xD425, 0xB7);
        LCD_WriteReg(0xD426, 0x02);
        LCD_WriteReg(0xD427, 0xCF);
        LCD_WriteReg(0xD428, 0x02);
        LCD_WriteReg(0xD429, 0xDE);
        LCD_WriteReg(0xD42A, 0x02);
        LCD_WriteReg(0xD42B, 0xF2);
        LCD_WriteReg(0xD42C, 0x02);
        LCD_WriteReg(0xD42D, 0xFE);
        LCD_WriteReg(0xD42E, 0x03);
        LCD_WriteReg(0xD42F, 0x10);
        LCD_WriteReg(0xD430, 0x03);
        LCD_WriteReg(0xD431, 0x33);
        LCD_WriteReg(0xD432, 0x03);
        LCD_WriteReg(0xD433, 0x6D);
        LCD_WriteReg(0xD500, 0x00);
        LCD_WriteReg(0xD501, 0x33);
        LCD_WriteReg(0xD502, 0x00);
        LCD_WriteReg(0xD503, 0x34);
        LCD_WriteReg(0xD504, 0x00);
        LCD_WriteReg(0xD505, 0x3A);
        LCD_WriteReg(0xD506, 0x00);
        LCD_WriteReg(0xD507, 0x4A);
        LCD_WriteReg(0xD508, 0x00);
        LCD_WriteReg(0xD509, 0x5C);
        LCD_WriteReg(0xD50A, 0x00);
        LCD_WriteReg(0xD50B, 0x81);

        LCD_WriteReg(0xD50C, 0x00);
        LCD_WriteReg(0xD50D, 0xA6);
        LCD_WriteReg(0xD50E, 0x00);
        LCD_WriteReg(0xD50F, 0xE5);
        LCD_WriteReg(0xD510, 0x01);
        LCD_WriteReg(0xD511, 0x13);
        LCD_WriteReg(0xD512, 0x01);
        LCD_WriteReg(0xD513, 0x54);
        LCD_WriteReg(0xD514, 0x01);
        LCD_WriteReg(0xD515, 0x82);
        LCD_WriteReg(0xD516, 0x01);
        LCD_WriteReg(0xD517, 0xCA);
        LCD_WriteReg(0xD518, 0x02);
        LCD_WriteReg(0xD519, 0x00);
        LCD_WriteReg(0xD51A, 0x02);
        LCD_WriteReg(0xD51B, 0x01);
        LCD_WriteReg(0xD51C, 0x02);
        LCD_WriteReg(0xD51D, 0x34);
        LCD_WriteReg(0xD51E, 0x02);
        LCD_WriteReg(0xD51F, 0x67);
        LCD_WriteReg(0xD520, 0x02);
        LCD_WriteReg(0xD521, 0x84);
        LCD_WriteReg(0xD522, 0x02);
        LCD_WriteReg(0xD523, 0xA4);
        LCD_WriteReg(0xD524, 0x02);
        LCD_WriteReg(0xD525, 0xB7);
        LCD_WriteReg(0xD526, 0x02);
        LCD_WriteReg(0xD527, 0xCF);
        LCD_WriteReg(0xD528, 0x02);
        LCD_WriteReg(0xD529, 0xDE);
        LCD_WriteReg(0xD52A, 0x02);
        LCD_WriteReg(0xD52B, 0xF2);
        LCD_WriteReg(0xD52C, 0x02);
        LCD_WriteReg(0xD52D, 0xFE);
        LCD_WriteReg(0xD52E, 0x03);
        LCD_WriteReg(0xD52F, 0x10);
        LCD_WriteReg(0xD530, 0x03);
        LCD_WriteReg(0xD531, 0x33);
        LCD_WriteReg(0xD532, 0x03);
        LCD_WriteReg(0xD533, 0x6D);
        LCD_WriteReg(0xD600, 0x00);
        LCD_WriteReg(0xD601, 0x33);
        LCD_WriteReg(0xD602, 0x00);
        LCD_WriteReg(0xD603, 0x34);
        LCD_WriteReg(0xD604, 0x00);
        LCD_WriteReg(0xD605, 0x3A);
        LCD_WriteReg(0xD606, 0x00);
        LCD_WriteReg(0xD607, 0x4A);
        LCD_WriteReg(0xD608, 0x00);
        LCD_WriteReg(0xD609, 0x5C);
        LCD_WriteReg(0xD60A, 0x00);
        LCD_WriteReg(0xD60B, 0x81);

        LCD_WriteReg(0xD60C, 0x00);
        LCD_WriteReg(0xD60D, 0xA6);
        LCD_WriteReg(0xD60E, 0x00);
        LCD_WriteReg(0xD60F, 0xE5);
        LCD_WriteReg(0xD610, 0x01);
        LCD_WriteReg(0xD611, 0x13);
        LCD_WriteReg(0xD612, 0x01);
        LCD_WriteReg(0xD613, 0x54);
        LCD_WriteReg(0xD614, 0x01);
        LCD_WriteReg(0xD615, 0x82);
        LCD_WriteReg(0xD616, 0x01);
        LCD_WriteReg(0xD617, 0xCA);
        LCD_WriteReg(0xD618, 0x02);
        LCD_WriteReg(0xD619, 0x00);
        LCD_WriteReg(0xD61A, 0x02);
        LCD_WriteReg(0xD61B, 0x01);
        LCD_WriteReg(0xD61C, 0x02);
        LCD_WriteReg(0xD61D, 0x34);
        LCD_WriteReg(0xD61E, 0x02);
        LCD_WriteReg(0xD61F, 0x67);
        LCD_WriteReg(0xD620, 0x02);
        LCD_WriteReg(0xD621, 0x84);
        LCD_WriteReg(0xD622, 0x02);
        LCD_WriteReg(0xD623, 0xA4);
        LCD_WriteReg(0xD624, 0x02);
        LCD_WriteReg(0xD625, 0xB7);
        LCD_WriteReg(0xD626, 0x02);
        LCD_WriteReg(0xD627, 0xCF);
        LCD_WriteReg(0xD628, 0x02);
        LCD_WriteReg(0xD629, 0xDE);
        LCD_WriteReg(0xD62A, 0x02);
        LCD_WriteReg(0xD62B, 0xF2);
        LCD_WriteReg(0xD62C, 0x02);
        LCD_WriteReg(0xD62D, 0xFE);
        LCD_WriteReg(0xD62E, 0x03);
        LCD_WriteReg(0xD62F, 0x10);
        LCD_WriteReg(0xD630, 0x03);
        LCD_WriteReg(0xD631, 0x33);
        LCD_WriteReg(0xD632, 0x03);
        LCD_WriteReg(0xD633, 0x6D);
        //LV2 Page 0 enable
        LCD_WriteReg(0xF000, 0x55);
        LCD_WriteReg(0xF001, 0xAA);
        LCD_WriteReg(0xF002, 0x52);
        LCD_WriteReg(0xF003, 0x08);
        LCD_WriteReg(0xF004, 0x00);
        //Display control
        LCD_WriteReg(0xB100, 0xCC);
        LCD_WriteReg(0xB101, 0x00);
        //Source hold time
        LCD_WriteReg(0xB600, 0x05);
        //Gate EQ control
        LCD_WriteReg(0xB700, 0x70);
        LCD_WriteReg(0xB701, 0x70);
        //Source EQ control (Mode 2)
        LCD_WriteReg(0xB800, 0x01);
        LCD_WriteReg(0xB801, 0x03);
        LCD_WriteReg(0xB802, 0x03);
        LCD_WriteReg(0xB803, 0x03);
        //Inversion mode (2-dot)
        LCD_WriteReg(0xBC00, 0x02);
        LCD_WriteReg(0xBC01, 0x00);
        LCD_WriteReg(0xBC02, 0x00);
        //Timing control 4H w/ 4-delay
        LCD_WriteReg(0xC900, 0xD0);
        LCD_WriteReg(0xC901, 0x02);
        LCD_WriteReg(0xC902, 0x50);
        LCD_WriteReg(0xC903, 0x50);
        LCD_WriteReg(0xC904, 0x50);
        LCD_WriteReg(0x3500, 0x00);
        LCD_WriteReg(0x3A00, 0x55); //16-bit/pixel
        LCD_WR_REG(0x1100);
        delay_us(120);
        LCD_WR_REG(0x2900);
    }
    else if (lcddev.id == 0X1963)
    {
        LCD_WR_REG(0xE2);       //Set PLL with OSC = 10MHz (hardware),	Multiplier N = 35, 250MHz < VCO < 800MHz = OSC*(N+1), VCO = 300MHz
        LCD_WR_DATA(0x1D);      //参数1
        LCD_WR_DATA(0x02);      //参数2 Divider M = 2, PLL = 300/(M+1) = 100MHz
        LCD_WR_DATA(0x04);      //参数3 Validate M and N values
        delay_us(100);
        LCD_WR_REG(0xE0);       // Start PLL command
        LCD_WR_DATA(0x01);      // enable PLL
        delay_ms(10);
        LCD_WR_REG(0xE0);       // Start PLL command again
        LCD_WR_DATA(0x03);      // now, use PLL output as system clock
        delay_ms(12);
        LCD_WR_REG(0x01);       //软复位
        delay_ms(10);

        LCD_WR_REG(0xE6);       //设置像素频率,33Mhz
        LCD_WR_DATA(0x2F);
        LCD_WR_DATA(0xFF);
        LCD_WR_DATA(0xFF);

        LCD_WR_REG(0xB0);       //设置LCD模式
        LCD_WR_DATA(0x20);      //24位模式
        LCD_WR_DATA(0x00);      //TFT 模式

        LCD_WR_DATA((SSD_HOR_RESOLUTION - 1) >> 8); //设置LCD水平像素
        LCD_WR_DATA(SSD_HOR_RESOLUTION - 1);
        LCD_WR_DATA((SSD_VER_RESOLUTION - 1) >> 8); //设置LCD垂直像素
        LCD_WR_DATA(SSD_VER_RESOLUTION - 1);
        LCD_WR_DATA(0x00);      //RGB序列

        LCD_WR_REG(0xB4);       //Set horizontal period
        LCD_WR_DATA((SSD_HT - 1) >> 8);
        LCD_WR_DATA(SSD_HT - 1);
        LCD_WR_DATA(SSD_HPS >> 8);
        LCD_WR_DATA(SSD_HPS);
        LCD_WR_DATA(SSD_HOR_PULSE_WIDTH - 1);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_REG(0xB6);       //Set vertical period
        LCD_WR_DATA((SSD_VT - 1) >> 8);
        LCD_WR_DATA(SSD_VT - 1);
        LCD_WR_DATA(SSD_VPS >> 8);
        LCD_WR_DATA(SSD_VPS);
        LCD_WR_DATA(SSD_VER_FRONT_PORCH - 1);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xF0);       //设置SSD1963与CPU接口为16bit
        LCD_WR_DATA(0x03);      //16-bit(565 format) data for 16bpp

        LCD_WR_REG(0x29);       //开启显示
        //设置PWM输出  背光通过占空比可调
        LCD_WR_REG(0xD0);       //设置自动白平衡DBC
        LCD_WR_DATA(0x00);      //disable

        LCD_WR_REG(0xBE);       //配置PWM输出
        LCD_WR_DATA(0x05);      //1设置PWM频率
        LCD_WR_DATA(0xFE);      //2设置PWM占空比
        LCD_WR_DATA(0x01);      //3设置C
        LCD_WR_DATA(0x00);      //4设置D
        LCD_WR_DATA(0x00);      //5设置E
        LCD_WR_DATA(0x00);      //6设置F

        LCD_WR_REG(0xB8);       //设置GPIO配置
        LCD_WR_DATA(0x03);      //2个IO口设置成输出
        LCD_WR_DATA(0x01);      //GPIO使用正常的IO功能
        LCD_WR_REG(0xBA);
        LCD_WR_DATA(0X01);      //GPIO[1:0]=01,控制LCD方向

        LCD_SSD_BackLightSet(100);//背光设置为最亮
    }
    
    LCD_Display_Dir(0);         //默认为竖屏
    LCD_LED = 1;                //点亮背光
    LCD_Clear(WHITE);
}
  
//清屏函数
//color:要清屏的填充色
void LCD_Clear(u16 color)
{
    u32 index = 0;
    u32 totalpoint = lcddev.width;
    totalpoint *= lcddev.height;    //得到总点数

    LCD_SetCursor(0x00, 0x0000);    //设置光标位置
    LCD_WriteRAM_Prepare();         //开始写入GRAM

    for (index = 0; index < totalpoint; index++)
    {
        LCD_WR_DATA(color);
    }
}

//在指定区域内填充指定颜色
//区域大小:(xend-xsta+1)*(yend-ysta+1)
//xsta
//color:要填充的颜色
void LCD_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 color)
{
    u16 i, j;
    u16 xlen = 0;

    xlen = ex - sx + 1;

    for (i = sy; i <= ey; i++)
    {
        LCD_SetCursor(sx, i);       //设置光标位置
        LCD_WriteRAM_Prepare();     //开始写入GRAM

        for (j = 0; j < xlen; j++)
        {
            LCD_WR_DATA(color);     //设置光标位置
        }
    }
}

//在指定区域内填充指定颜色块
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)
//color:要填充的颜色
void LCD_Color_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 *color)
{
    u16 height, width;
    u16 i, j;
    width = ex - sx + 1;            //得到填充的宽度
    height = ey - sy + 1;           //高度

    for (i = 0; i < height; i++)
    {
        LCD_SetCursor(sx, sy + i);  //设置光标位置
        LCD_WriteRAM_Prepare();     //开始写入GRAM

        for (j = 0; j < width; j++)
        {
            LCD_WR_DATA(color[i * width + j]); //写入数据
        }
    }
}

//画线
//x1,y1:起点坐标
//x2,y2:终点坐标  
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2)
{
    u16 t;
    int xerr = 0, yerr = 0, delta_x, delta_y, distance;
    int incx, incy, uRow, uCol;
    delta_x = x2 - x1;              //计算坐标增量
    delta_y = y2 - y1;
    uRow = x1;
    uCol = y1;

    if (delta_x > 0)incx = 1;       //设置单步方向
    else if (delta_x == 0)incx = 0; //垂直线
    else
    {
        incx = -1;
        delta_x = -delta_x;
    }

    if (delta_y > 0)incy = 1;
    else if (delta_y == 0)incy = 0; //水平线
    else
    {
        incy = -1;
        delta_y = -delta_y;
    }

    if ( delta_x > delta_y)distance = delta_x; //选取基本增量坐标轴
    else distance = delta_y;

    for (t = 0; t <= distance + 1; t++ )    //画线输出
    {
        LCD_DrawPoint(uRow, uCol); //画点
        xerr += delta_x ;
        yerr += delta_y ;

        if (xerr > distance)
        {
            xerr -= distance;
            uRow += incx;
        }

        if (yerr > distance)
        {
            yerr -= distance;
            uCol += incy;
        }
    }
}

//画矩形
//(x1,y1),(x2,y2):矩形的对角坐标
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2)
{
    LCD_DrawLine(x1, y1, x2, y1);
    LCD_DrawLine(x1, y1, x1, y2);
    LCD_DrawLine(x1, y2, x2, y2);
    LCD_DrawLine(x2, y1, x2, y2);
}

//在指定位置画一个指定大小的圆
//(x,y):中心点
//r    :半径
void LCD_Draw_Circle(u16 x0,u16 y0,u8 r)
{
    int a, b;
    int di;
    a = 0;
    b = r;
    di = 3 - (r << 1);       //判断下个点位置的标志

    while (a <= b)
    {
        LCD_DrawPoint(x0 + a, y0 - b);        //5
        LCD_DrawPoint(x0 + b, y0 - a);        //0
        LCD_DrawPoint(x0 + b, y0 + a);        //4
        LCD_DrawPoint(x0 + a, y0 + b);        //6
        LCD_DrawPoint(x0 - a, y0 + b);        //1
        LCD_DrawPoint(x0 - b, y0 + a);
        LCD_DrawPoint(x0 - a, y0 - b);        //2
        LCD_DrawPoint(x0 - b, y0 - a);        //7
        a++;

        //使用Bresenham算法画圆
        if (di < 0)di += 4 * a + 6;
        else
        {
            di += 10 + 4 * (a - b);
            b--;
        }
    }
}

//在指定位置显示一个字符
//x,y:起始坐标
//num:要显示的字符:" "--->"~"
//size:字体大小 12/16/24
//mode:叠加方式(1)还是非叠加方式(0)
void LCD_ShowChar(u16 x,u16 y,u8 num,u8 size,u8 mode)
{
    u8 temp, t1, t;
    u16 y0 = y;
    u8 csize = (size / 8 + ((size % 8) ? 1 : 0)) * (size / 2);  //得到字体一个字符对应点阵集所占的字节数
    num = num - ' ';    //得到偏移后的值（ASCII字库是从空格开始取模，所以-' '就是对应字符的字库）

    for (t = 0; t < csize; t++)
    {
        if (size == 12)temp = asc2_1206[num][t];        //调用1206字体
        else if (size == 16)temp = asc2_1608[num][t];   //调用1608字体
        else if (size == 24)temp = asc2_2412[num][t];   //调用2412字体
        else return;                                    //没有的字库

        for (t1 = 0; t1 < 8; t1++)
        {
            if (temp & 0x80)LCD_Fast_DrawPoint(x, y, POINT_COLOR);
            else if (mode == 0)LCD_Fast_DrawPoint(x, y, BACK_COLOR);

            temp <<= 1;
            y++;

            if (y >= lcddev.height)return;      //超区域了

            if ((y - y0) == size)
            {
                y = y0;
                x++;

                if (x >= lcddev.width)return;   //超区域了

                break;
            }
        }
    } 
}

//m^n函数
//返回值:m^n次方.
u32 LCD_Pow(u8 m,u8 n)
{
    u32 result=1;
    while(n--)result*=m;    
    return result;
}

//显示数字,高位为0,则不显示
//x,y :起点坐标	 
//len :数字的位数
//size:字体大小
//color:颜色 
//num:数值(0~4294967295);
void LCD_ShowNum(u16 x,u16 y,u32 num,u8 len,u8 size)
{
    u8 t, temp;
    u8 enshow = 0;

    for (t = 0; t < len; t++)
    {
        temp = (num / LCD_Pow(10, len - t - 1)) % 10;

        if (enshow == 0 && t < (len - 1))
        {
            if (temp == 0)
            {
                LCD_ShowChar(x + (size / 2)*t, y, ' ', size, 0);
                continue;
            }
            else enshow = 1;

        }

        LCD_ShowChar(x + (size / 2)*t, y, temp + '0', size, 0);
    }
}

//显示数字,高位为0,还是显示
//x,y:起点坐标
//num:数值(0~999999999);
//len:长度(即要显示的位数)
//size:字体大小
//mode:
//[7]:0,不填充;1,填充0.
//[6:1]:保留
//[0]:0,非叠加显示;1,叠加显示.
void LCD_ShowxNum(u16 x,u16 y,u32 num,u8 len,u8 size,u8 mode)
{  
    u8 t, temp;
    u8 enshow = 0;

    for (t = 0; t < len; t++)
    {
        temp = (num / LCD_Pow(10, len - t - 1)) % 10;

        if (enshow == 0 && t < (len - 1))
        {
            if (temp == 0)
            {
                if (mode & 0X80)LCD_ShowChar(x + (size / 2)*t, y, '0', size, mode & 0X01);
                else LCD_ShowChar(x + (size / 2)*t, y, ' ', size, mode & 0X01);

                continue;
            }
            else enshow = 1;

        }

        LCD_ShowChar(x + (size / 2)*t, y, temp + '0', size, mode & 0X01);
    }
}

//显示字符串
//x,y:起点坐标
//width,height:区域大小
//size:字体大小
//*p:字符串起始地址
void LCD_ShowString(u16 x,u16 y,u16 width,u16 height,u8 size,u8 *p)
{         
    u8 x0 = x;
    width += x;
    height += y;

    while ((*p <= '~') && (*p >= ' '))   //判断是不是非法字符!
    {
        if (x >= width)
        {
            x = x0;
            y += size;
        }

        if (y >= height)break; //退出

        LCD_ShowChar(x, y, *p, size, 0);
        x += size / 2;
        p++;
    }
}

 lcd.h

#ifndef __LCD_H
#define __LCD_H		
#include "sys.h"	 
#include "stdlib.h"


//LCD重要参数集
typedef struct  
{
    u16 width;      //LCD 宽度
    u16 height;     //LCD 高度
    u16 id;         //LCD ID
    u8  dir;        //横屏还是竖屏控制：0，竖屏；1，横屏。
    u16 wramcmd;    //开始写gram指令
    u16 setxcmd;    //设置x坐标指令
    u16  setycmd;   //设置y坐标指令
} _lcd_dev;

//LCD参数
extern _lcd_dev lcddev; //管理LCD重要参数
//LCD的画笔颜色和背景色
extern u16  POINT_COLOR;//默认红色    
extern u16  BACK_COLOR; //背景颜色.默认为白色


//-----------------LCD端口定义---------------- 
#define LCD_LED PCout(10)               //LCD背光       PC10
 
#define LCD_CS_SET  GPIOC->BSRR=1<<9    //片选端口      PC9
#define LCD_RS_SET  GPIOC->BSRR=1<<8    //数据/命令     PC8
#define LCD_WR_SET  GPIOC->BSRR=1<<7    //写数据        PC7
#define LCD_RD_SET  GPIOC->BSRR=1<<6    //读数据        PC6

#define LCD_CS_CLR  GPIOC->BRR=1<<9     //片选端口      PC9
#define LCD_RS_CLR  GPIOC->BRR=1<<8     //数据/命令     PC8
#define LCD_WR_CLR  GPIOC->BRR=1<<7     //写数据        PC7
#define LCD_RD_CLR  GPIOC->BRR=1<<6     //读数据        PC6

//PB0~15,作为数据线
#define DATAOUT(x) GPIOB->ODR=x; //数据输出
#define DATAIN     GPIOB->IDR;   //数据输入

 
//
//扫描方向定义
#define L2R_U2D  0 //从左到右,从上到下
#define L2R_D2U  1 //从左到右,从下到上
#define R2L_U2D  2 //从右到左,从上到下
#define R2L_D2U  3 //从右到左,从下到上

#define U2D_L2R  4 //从上到下,从左到右
#define U2D_R2L  5 //从上到下,从右到左
#define D2U_L2R  6 //从下到上,从左到右
#define D2U_R2L  7 //从下到上,从右到左

#define DFT_SCAN_DIR  L2R_U2D  //默认的扫描方向

//扫描方向定义
#define L2R_U2D  0 //从左到右,从上到下
#define L2R_D2U  1 //从左到右,从下到上
#define R2L_U2D  2 //从右到左,从上到下
#define R2L_D2U  3 //从右到左,从下到上

#define U2D_L2R  4 //从上到下,从左到右
#define U2D_R2L  5 //从上到下,从右到左
#define D2U_L2R  6 //从下到上,从左到右
#define D2U_R2L  7 //从下到上,从右到左

#define DFT_SCAN_DIR  L2R_U2D  //默认的扫描方向

//画笔颜色
#define WHITE           0xFFFF
#define BLACK           0x0000
#define BLUE            0x001F
#define BRED            0XF81F
#define GRED            0XFFE0
#define GBLUE           0X07FF
#define RED             0xF800
#define MAGENTA         0xF81F
#define GREEN           0x07E0
#define CYAN            0x7FFF
#define YELLOW          0xFFE0
#define BROWN           0XBC40  //棕色
#define BRRED           0XFC07  //棕红色
#define GRAY            0X8430  //灰色
//GUI颜色

#define DARKBLUE        0X01CF  //深蓝色
#define LIGHTBLUE       0X7D7C  //浅蓝色  
#define GRAYBLUE        0X5458  //灰蓝色
//以上三色为PANEL的颜色

#define LIGHTGREEN      0X841F  //浅绿色 
#define LGRAY           0XC618  //浅灰色(PANNEL),窗体背景色

#define LGRAYBLUE       0XA651  //浅灰蓝色(中间层颜色)
#define LBBLUE          0X2B12  //浅棕蓝色(选择条目的反色)


void LCD_Init(void);                                                        //初始化
void LCD_DisplayOn(void);                                                   //开显示
void LCD_DisplayOff(void);                                                  //关显示
void LCD_Clear(u16 Color);                                                  //清屏
void LCD_SetCursor(u16 Xpos, u16 Ypos);                                     //设置光标
void LCD_DrawPoint(u16 x, u16 y);                                           //画点
void LCD_Fast_DrawPoint(u16 x, u16 y, u16 color);                           //快速画点
u16  LCD_ReadPoint(u16 x, u16 y);                                           //读点
void LCD_Draw_Circle(u16 x0, u16 y0, u8 r);                                 //画圆
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2);                          //画线
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2);                     //画矩形
void LCD_Fill(u16 sx, u16 sy, u16 ex, u16 ey, u16 color);                   //填充单色
void LCD_Color_Fill(u16 sx, u16 sy, u16 ex, u16 ey, u16 *color);            //填充指定颜色
void LCD_ShowChar(u16 x, u16 y, u8 num, u8 size, u8 mode);                  //显示一个字符
void LCD_ShowNum(u16 x, u16 y, u32 num, u8 len, u8 size);                   //显示一个数字
void LCD_ShowxNum(u16 x, u16 y, u32 num, u8 len, u8 size, u8 mode);         //显示 数字
void LCD_ShowString(u16 x, u16 y, u16 width, u16 height, u8 size, u8 *p);   //显示一个字符串,12/16字体

void LCD_WriteReg(u16 LCD_Reg, u16 LCD_RegValue);
u16 LCD_ReadReg(u16 LCD_Reg);
void LCD_WriteRAM_Prepare(void);
void LCD_WriteRAM(u16 RGB_Code);
void LCD_SSD_BackLightSet(u8 pwm);                          //SSD1963 背光控制
void LCD_Scan_Dir(u8 dir);                                  //设置屏扫描方向
void LCD_Display_Dir(u8 dir);                               //设置屏幕显示方向
void LCD_Set_Window(u16 sx, u16 sy, u16 width, u16 height); //设置窗口

//写数据函数
#define LCD_WR_DATA(data){\
        LCD_RS_SET;\
        LCD_CS_CLR;\
        DATAOUT(data);\
        LCD_WR_CLR;\
        LCD_WR_SET;\
        LCD_CS_SET;\
    }

//LCD分辨率设置
#define SSD_HOR_RESOLUTION      800     //LCD水平分辨率
#define SSD_VER_RESOLUTION      480     //LCD垂直分辨率
//LCD驱动参数设置
#define SSD_HOR_PULSE_WIDTH     1       //水平脉宽
#define SSD_HOR_BACK_PORCH      46      //水平前廊
#define SSD_HOR_FRONT_PORCH     210     //水平后廊

#define SSD_VER_PULSE_WIDTH     1       //垂直脉宽
#define SSD_VER_BACK_PORCH      23      //垂直前廊
#define SSD_VER_FRONT_PORCH     22      //垂直前廊
//如下几个参数，自动计算
#define SSD_HT  (SSD_HOR_RESOLUTION+SSD_HOR_BACK_PORCH+SSD_HOR_FRONT_PORCH)
#define SSD_HPS (SSD_HOR_BACK_PORCH)
#define SSD_VT  (SSD_VER_RESOLUTION+SSD_VER_BACK_PORCH+SSD_VER_FRONT_PORCH)
#define SSD_VPS (SSD_VER_BACK_PORCH)

#endif














#ifndef __FONT_H
#define __FONT_H 	   
//常用ASCII表
//偏移量32 
//ASCII字符集: !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~
//PC2LCD2002取模方式设置：阴码+逐列式+顺向+C51格式
//总共：3个字符集（12*12、16*16和24*24），用户可以自行新增其他分辨率的字符集。
//每个字符所占用的字节数为:(size/8+((size%8)?1:0))*(size/2),其中size:是字库生成时的点阵大小(12/16/24...)
 
//12*12 ASCII字符集点阵
const unsigned char asc2_1206[95][12]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x3F,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x30,0x00,0x40,0x00,0x30,0x00,0x40,0x00,0x00,0x00},/*""",2*/
{0x09,0x00,0x0B,0xC0,0x3D,0x00,0x0B,0xC0,0x3D,0x00,0x09,0x00},/*"#",3*/
{0x18,0xC0,0x24,0x40,0x7F,0xE0,0x22,0x40,0x31,0x80,0x00,0x00},/*"$",4*/
{0x18,0x00,0x24,0xC0,0x1B,0x00,0x0D,0x80,0x32,0x40,0x01,0x80},/*"%",5*/
{0x03,0x80,0x1C,0x40,0x27,0x40,0x1C,0x80,0x07,0x40,0x00,0x40},/*"&",6*/
{0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x80,0x20,0x40,0x40,0x20},/*"(",8*/
{0x00,0x00,0x40,0x20,0x20,0x40,0x1F,0x80,0x00,0x00,0x00,0x00},/*")",9*/
{0x09,0x00,0x06,0x00,0x1F,0x80,0x06,0x00,0x09,0x00,0x00,0x00},/*"*",10*/
{0x04,0x00,0x04,0x00,0x3F,0x80,0x04,0x00,0x04,0x00,0x00,0x00},/*"+",11*/
{0x00,0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x20,0x01,0xC0,0x06,0x00,0x38,0x00,0x40,0x00,0x00,0x00},/*"/",15*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"0",16*/
{0x00,0x00,0x10,0x40,0x3F,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"1",17*/
{0x18,0xC0,0x21,0x40,0x22,0x40,0x24,0x40,0x18,0x40,0x00,0x00},/*"2",18*/
{0x10,0x80,0x20,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"3",19*/
{0x02,0x00,0x0D,0x00,0x11,0x00,0x3F,0xC0,0x01,0x40,0x00,0x00},/*"4",20*/
{0x3C,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x23,0x80,0x00,0x00},/*"5",21*/
{0x1F,0x80,0x24,0x40,0x24,0x40,0x34,0x40,0x03,0x80,0x00,0x00},/*"6",22*/
{0x30,0x00,0x20,0x00,0x27,0xC0,0x38,0x00,0x20,0x00,0x00,0x00},/*"7",23*/
{0x1B,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"8",24*/
{0x1C,0x00,0x22,0xC0,0x22,0x40,0x22,0x40,0x1F,0x80,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x08,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x04,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x04,0x00,0x0A,0x00,0x11,0x00,0x20,0x80,0x40,0x40},/*"<",28*/
{0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x40,0x40,0x20,0x80,0x11,0x00,0x0A,0x00,0x04,0x00},/*">",30*/
{0x18,0x00,0x20,0x00,0x23,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"?",31*/
{0x1F,0x80,0x20,0x40,0x27,0x40,0x29,0x40,0x1F,0x40,0x00,0x00},/*"@",32*/
{0x00,0x40,0x07,0xC0,0x39,0x00,0x0F,0x00,0x01,0xC0,0x00,0x40},/*"A",33*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"B",34*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x30,0x80,0x00,0x00},/*"C",35*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"D",36*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x40,0x30,0xC0,0x00,0x00},/*"E",37*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x00,0x30,0x00,0x00,0x00},/*"F",38*/
{0x0F,0x00,0x10,0x80,0x20,0x40,0x22,0x40,0x33,0x80,0x02,0x00},/*"G",39*/
{0x20,0x40,0x3F,0xC0,0x04,0x00,0x04,0x00,0x3F,0xC0,0x20,0x40},/*"H",40*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x00,0x00},/*"I",41*/
{0x00,0x60,0x20,0x20,0x20,0x20,0x3F,0xC0,0x20,0x00,0x20,0x00},/*"J",42*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x0B,0x00,0x30,0xC0,0x20,0x40},/*"K",43*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x00,0x40,0x00,0x40,0x00,0xC0},/*"L",44*/
{0x3F,0xC0,0x3C,0x00,0x03,0xC0,0x3C,0x00,0x3F,0xC0,0x00,0x00},/*"M",45*/
{0x20,0x40,0x3F,0xC0,0x0C,0x40,0x23,0x00,0x3F,0xC0,0x20,0x00},/*"N",46*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"O",47*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"P",48*/
{0x1F,0x80,0x21,0x40,0x21,0x40,0x20,0xE0,0x1F,0xA0,0x00,0x00},/*"Q",49*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x26,0x00,0x19,0xC0,0x00,0x40},/*"R",50*/
{0x18,0xC0,0x24,0x40,0x24,0x40,0x22,0x40,0x31,0x80,0x00,0x00},/*"S",51*/
{0x30,0x00,0x20,0x40,0x3F,0xC0,0x20,0x40,0x30,0x00,0x00,0x00},/*"T",52*/
{0x20,0x00,0x3F,0x80,0x00,0x40,0x00,0x40,0x3F,0x80,0x20,0x00},/*"U",53*/
{0x20,0x00,0x3E,0x00,0x01,0xC0,0x07,0x00,0x38,0x00,0x20,0x00},/*"V",54*/
{0x38,0x00,0x07,0xC0,0x3C,0x00,0x07,0xC0,0x38,0x00,0x00,0x00},/*"W",55*/
{0x20,0x40,0x39,0xC0,0x06,0x00,0x39,0xC0,0x20,0x40,0x00,0x00},/*"X",56*/
{0x20,0x00,0x38,0x40,0x07,0xC0,0x38,0x40,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x30,0x40,0x21,0xC0,0x26,0x40,0x38,0x40,0x20,0xC0,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x7F,0xE0,0x40,0x20,0x40,0x20,0x00,0x00},/*"[",59*/
{0x00,0x00,0x70,0x00,0x0C,0x00,0x03,0x80,0x00,0x40,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x20,0x40,0x20,0x7F,0xE0,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x20,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10},/*"_",63*/
{0x00,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x02,0x80,0x05,0x40,0x05,0x40,0x03,0xC0,0x00,0x40},/*"a",65*/
{0x20,0x00,0x3F,0xC0,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"b",66*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x06,0x40,0x00,0x00},/*"c",67*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x24,0x40,0x3F,0xC0,0x00,0x40},/*"d",68*/
{0x00,0x00,0x03,0x80,0x05,0x40,0x05,0x40,0x03,0x40,0x00,0x00},/*"e",69*/
{0x00,0x00,0x04,0x40,0x1F,0xC0,0x24,0x40,0x24,0x40,0x20,0x00},/*"f",70*/
{0x00,0x00,0x02,0xE0,0x05,0x50,0x05,0x50,0x06,0x50,0x04,0x20},/*"g",71*/
{0x20,0x40,0x3F,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"h",72*/
{0x00,0x00,0x04,0x40,0x27,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x10,0x00,0x10,0x04,0x10,0x27,0xE0,0x00,0x00,0x00,0x00},/*"j",74*/
{0x20,0x40,0x3F,0xC0,0x01,0x40,0x07,0x00,0x04,0xC0,0x04,0x40},/*"k",75*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x00,0x40,0x00,0x40,0x00,0x00},/*"l",76*/
{0x07,0xC0,0x04,0x00,0x07,0xC0,0x04,0x00,0x03,0xC0,0x00,0x00},/*"m",77*/
{0x04,0x40,0x07,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"n",78*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"o",79*/
{0x04,0x10,0x07,0xF0,0x04,0x50,0x04,0x40,0x03,0x80,0x00,0x00},/*"p",80*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x50,0x07,0xF0,0x00,0x10},/*"q",81*/
{0x04,0x40,0x07,0xC0,0x02,0x40,0x04,0x00,0x04,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x06,0x40,0x05,0x40,0x05,0x40,0x04,0xC0,0x00,0x00},/*"s",83*/
{0x00,0x00,0x04,0x00,0x1F,0x80,0x04,0x40,0x00,0x40,0x00,0x00},/*"t",84*/
{0x04,0x00,0x07,0x80,0x00,0x40,0x04,0x40,0x07,0xC0,0x00,0x40},/*"u",85*/
{0x04,0x00,0x07,0x00,0x04,0xC0,0x01,0x80,0x06,0x00,0x04,0x00},/*"v",86*/
{0x06,0x00,0x01,0xC0,0x07,0x00,0x01,0xC0,0x06,0x00,0x00,0x00},/*"w",87*/
{0x04,0x40,0x06,0xC0,0x01,0x00,0x06,0xC0,0x04,0x40,0x00,0x00},/*"x",88*/
{0x04,0x10,0x07,0x10,0x04,0xE0,0x01,0x80,0x06,0x00,0x04,0x00},/*"y",89*/
{0x00,0x00,0x04,0x40,0x05,0xC0,0x06,0x40,0x04,0x40,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x7B,0xE0,0x40,0x20,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xF0,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x20,0x7B,0xE0,0x04,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x40,0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x40,0x00},/*"~",94*/
};  
//16*16 ASCII字符集点阵
const unsigned char asc2_1608[95][16]={	  
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xCC,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x00,0x00},/*""",2*/
{0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x00,0x00},/*"#",3*/
{0x00,0x00,0x0E,0x18,0x11,0x04,0x3F,0xFF,0x10,0x84,0x0C,0x78,0x00,0x00,0x00,0x00},/*"$",4*/
{0x0F,0x00,0x10,0x84,0x0F,0x38,0x00,0xC0,0x07,0x78,0x18,0x84,0x00,0x78,0x00,0x00},/*"%",5*/
{0x00,0x78,0x0F,0x84,0x10,0xC4,0x11,0x24,0x0E,0x98,0x00,0xE4,0x00,0x84,0x00,0x08},/*"&",6*/
{0x08,0x00,0x68,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xE0,0x18,0x18,0x20,0x04,0x40,0x02,0x00,0x00},/*"(",8*/
{0x00,0x00,0x40,0x02,0x20,0x04,0x18,0x18,0x07,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x02,0x40,0x02,0x40,0x01,0x80,0x0F,0xF0,0x01,0x80,0x02,0x40,0x02,0x40,0x00,0x00},/*"*",10*/
{0x00,0x80,0x00,0x80,0x00,0x80,0x0F,0xF8,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00},/*"+",11*/
{0x00,0x01,0x00,0x0D,0x00,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80},/*"-",13*/
{0x00,0x00,0x00,0x0C,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x06,0x00,0x18,0x00,0x60,0x01,0x80,0x06,0x00,0x18,0x00,0x20,0x00},/*"/",15*/
{0x00,0x00,0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"0",16*/
{0x00,0x00,0x08,0x04,0x08,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x0C,0x10,0x14,0x10,0x24,0x10,0x44,0x11,0x84,0x0E,0x0C,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0C,0x18,0x10,0x04,0x11,0x04,0x11,0x04,0x12,0x88,0x0C,0x70,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0xE0,0x03,0x20,0x04,0x24,0x08,0x24,0x1F,0xFC,0x00,0x24,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x98,0x10,0x84,0x11,0x04,0x11,0x04,0x10,0x88,0x10,0x70,0x00,0x00},/*"5",21*/
{0x00,0x00,0x07,0xF0,0x08,0x88,0x11,0x04,0x11,0x04,0x18,0x88,0x00,0x70,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1C,0x00,0x10,0x00,0x10,0xFC,0x13,0x00,0x1C,0x00,0x10,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x38,0x11,0x44,0x10,0x84,0x10,0x84,0x11,0x44,0x0E,0x38,0x00,0x00},/*"8",24*/
{0x00,0x00,0x07,0x00,0x08,0x8C,0x10,0x44,0x10,0x44,0x08,0x88,0x07,0xF0,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x03,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x80,0x01,0x40,0x02,0x20,0x04,0x10,0x08,0x08,0x10,0x04,0x00,0x00},/*"<",28*/
{0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x00,0x00},/*"=",29*/
{0x00,0x00,0x10,0x04,0x08,0x08,0x04,0x10,0x02,0x20,0x01,0x40,0x00,0x80,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x00,0x12,0x00,0x10,0x0C,0x10,0x6C,0x10,0x80,0x0F,0x00,0x00,0x00},/*"?",31*/
{0x03,0xE0,0x0C,0x18,0x13,0xE4,0x14,0x24,0x17,0xC4,0x08,0x28,0x07,0xD0,0x00,0x00},/*"@",32*/
{0x00,0x04,0x00,0x3C,0x03,0xC4,0x1C,0x40,0x07,0x40,0x00,0xE4,0x00,0x1C,0x00,0x04},/*"A",33*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x11,0x04,0x0E,0x88,0x00,0x70,0x00,0x00},/*"B",34*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x08,0x1C,0x10,0x00,0x00},/*"C",35*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"D",36*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x17,0xC4,0x10,0x04,0x08,0x18,0x00,0x00},/*"E",37*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x17,0xC0,0x10,0x00,0x08,0x00,0x00,0x00},/*"F",38*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x44,0x1C,0x78,0x00,0x40,0x00,0x00},/*"G",39*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x00,0x80,0x00,0x80,0x10,0x84,0x1F,0xFC,0x10,0x04},/*"H",40*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x03,0x00,0x01,0x10,0x01,0x10,0x01,0x1F,0xFE,0x10,0x00,0x10,0x00,0x00,0x00},/*"J",42*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x03,0x80,0x14,0x64,0x18,0x1C,0x10,0x04,0x00,0x00},/*"K",43*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x0C,0x00,0x00},/*"L",44*/
{0x10,0x04,0x1F,0xFC,0x1F,0x00,0x00,0xFC,0x1F,0x00,0x1F,0xFC,0x10,0x04,0x00,0x00},/*"M",45*/
{0x10,0x04,0x1F,0xFC,0x0C,0x04,0x03,0x00,0x00,0xE0,0x10,0x18,0x1F,0xFC,0x10,0x00},/*"N",46*/
{0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"O",47*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x10,0x80,0x10,0x80,0x10,0x80,0x0F,0x00,0x00,0x00},/*"P",48*/
{0x07,0xF0,0x08,0x18,0x10,0x24,0x10,0x24,0x10,0x1C,0x08,0x0A,0x07,0xF2,0x00,0x00},/*"Q",49*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x11,0xC0,0x11,0x30,0x0E,0x0C,0x00,0x04},/*"R",50*/
{0x00,0x00,0x0E,0x1C,0x11,0x04,0x10,0x84,0x10,0x84,0x10,0x44,0x1C,0x38,0x00,0x00},/*"S",51*/
{0x18,0x00,0x10,0x00,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x00,0x18,0x00,0x00,0x00},/*"T",52*/
{0x10,0x00,0x1F,0xF8,0x10,0x04,0x00,0x04,0x00,0x04,0x10,0x04,0x1F,0xF8,0x10,0x00},/*"U",53*/
{0x10,0x00,0x1E,0x00,0x11,0xE0,0x00,0x1C,0x00,0x70,0x13,0x80,0x1C,0x00,0x10,0x00},/*"V",54*/
{0x1F,0xC0,0x10,0x3C,0x00,0xE0,0x1F,0x00,0x00,0xE0,0x10,0x3C,0x1F,0xC0,0x00,0x00},/*"W",55*/
{0x10,0x04,0x18,0x0C,0x16,0x34,0x01,0xC0,0x01,0xC0,0x16,0x34,0x18,0x0C,0x10,0x04},/*"X",56*/
{0x10,0x00,0x1C,0x00,0x13,0x04,0x00,0xFC,0x13,0x04,0x1C,0x00,0x10,0x00,0x00,0x00},/*"Y",57*/
{0x08,0x04,0x10,0x1C,0x10,0x64,0x10,0x84,0x13,0x04,0x1C,0x04,0x10,0x18,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFE,0x40,0x02,0x40,0x02,0x40,0x02,0x00,0x00},/*"[",59*/
{0x00,0x00,0x30,0x00,0x0C,0x00,0x03,0x80,0x00,0x60,0x00,0x1C,0x00,0x03,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x40,0x02,0x7F,0xFE,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00},/*"^",62*/
{0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01},/*"_",63*/
{0x00,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x98,0x01,0x24,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xFC,0x00,0x04},/*"a",65*/
{0x10,0x00,0x1F,0xFC,0x00,0x88,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x11,0x08,0x1F,0xFC,0x00,0x04},/*"d",68*/
{0x00,0x00,0x00,0xF8,0x01,0x44,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xC8,0x00,0x00},/*"e",69*/
{0x00,0x00,0x01,0x04,0x01,0x04,0x0F,0xFC,0x11,0x04,0x11,0x04,0x11,0x00,0x18,0x00},/*"f",70*/
{0x00,0x00,0x00,0xD6,0x01,0x29,0x01,0x29,0x01,0x29,0x01,0xC9,0x01,0x06,0x00,0x00},/*"g",71*/
{0x10,0x04,0x1F,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"h",72*/
{0x00,0x00,0x01,0x04,0x19,0x04,0x19,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x03,0x00,0x01,0x01,0x01,0x19,0x01,0x19,0xFE,0x00,0x00,0x00,0x00},/*"j",74*/
{0x10,0x04,0x1F,0xFC,0x00,0x24,0x00,0x40,0x01,0xB4,0x01,0x0C,0x01,0x04,0x00,0x00},/*"k",75*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"l",76*/
{0x01,0x04,0x01,0xFC,0x01,0x04,0x01,0x00,0x01,0xFC,0x01,0x04,0x01,0x00,0x00,0xFC},/*"m",77*/
{0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"n",78*/
{0x00,0x00,0x00,0xF8,0x01,0x04,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0xF8,0x00,0x00},/*"o",79*/
{0x01,0x01,0x01,0xFF,0x00,0x85,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x05,0x01,0xFF,0x00,0x01},/*"q",81*/
{0x01,0x04,0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x04,0x01,0x00,0x01,0x80,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0xCC,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x98,0x00,0x00},/*"s",83*/
{0x00,0x00,0x01,0x00,0x01,0x00,0x07,0xF8,0x01,0x04,0x01,0x04,0x00,0x00,0x00,0x00},/*"t",84*/
{0x01,0x00,0x01,0xF8,0x00,0x04,0x00,0x04,0x00,0x04,0x01,0x08,0x01,0xFC,0x00,0x04},/*"u",85*/
{0x01,0x00,0x01,0x80,0x01,0x70,0x00,0x0C,0x00,0x10,0x01,0x60,0x01,0x80,0x01,0x00},/*"v",86*/
{0x01,0xF0,0x01,0x0C,0x00,0x30,0x01,0xC0,0x00,0x30,0x01,0x0C,0x01,0xF0,0x01,0x00},/*"w",87*/
{0x00,0x00,0x01,0x04,0x01,0x8C,0x00,0x74,0x01,0x70,0x01,0x8C,0x01,0x04,0x00,0x00},/*"x",88*/
{0x01,0x01,0x01,0x81,0x01,0x71,0x00,0x0E,0x00,0x18,0x01,0x60,0x01,0x80,0x01,0x00},/*"y",89*/
{0x00,0x00,0x01,0x84,0x01,0x0C,0x01,0x34,0x01,0x44,0x01,0x84,0x01,0x0C,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x3E,0xFC,0x40,0x02,0x40,0x02},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x3E,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x60,0x00,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00},/*"~",94*/
};  
//24*24 ASICII字符集点阵
const unsigned char asc2_2412[95][36]={	  
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x80,0x38,0x0F,0xFE,0x38,0x0F,0x80,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x31,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xE0,0xF0,0x06,0x30,0x08,0x04,0x18,0x08,0x1F,0xFF,0xFE,0x04,0x0E,0x08,0x07,0x87,0xF0,0x03,0x81,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"$",4*/
{0x01,0xF0,0x00,0x06,0x0C,0x00,0x04,0x04,0x08,0x06,0x0C,0x70,0x01,0xF9,0xC0,0x00,0x0E,0x00,0x00,0x3B,0xE0,0x00,0xEC,0x18,0x07,0x08,0x08,0x04,0x0C,0x18,0x00,0x03,0xE0,0x00,0x00,0x00},/*"%",5*/
{0x00,0x01,0xE0,0x00,0x07,0xF0,0x03,0xF8,0x18,0x04,0x1C,0x08,0x04,0x17,0x08,0x07,0xE1,0xD0,0x03,0xC0,0xE0,0x00,0x23,0xB0,0x00,0x3C,0x08,0x00,0x20,0x08,0x00,0x00,0x10,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x01,0xFF,0xC0,0x07,0x80,0xF0,0x0C,0x00,0x18,0x10,0x00,0x04,0x20,0x00,0x02,0x00,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x20,0x00,0x02,0x10,0x00,0x04,0x0C,0x00,0x18,0x07,0x80,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x42,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x3C,0x00,0x00,0x18,0x00,0x03,0xFF,0xC0,0x00,0x18,0x00,0x00,0x3C,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x42,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x01,0xFF,0xC0,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x1C,0x00,0x00,0x70,0x00,0x01,0x80,0x00,0x0E,0x00,0x00,0x38,0x00,0x00,0xC0,0x00,0x07,0x00,0x00,0x1C,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x08,0x01,0x00,0x08,0x01,0x00,0x08,0x03,0xFF,0xF8,0x07,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x01,0xC0,0x38,0x02,0xC0,0x58,0x04,0x00,0x98,0x04,0x01,0x18,0x04,0x02,0x18,0x04,0x04,0x18,0x06,0x1C,0x18,0x03,0xF8,0x18,0x01,0xE0,0xF8,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xC0,0xF0,0x04,0x00,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x0D,0x00,0x00,0x11,0x00,0x00,0x61,0x00,0x00,0x81,0x08,0x03,0x01,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x08,0x00,0x01,0x08,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0xE0,0x07,0xFC,0xD0,0x06,0x08,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x18,0x38,0x06,0x0F,0xF0,0x06,0x07,0xC0,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x84,0x30,0x02,0x08,0x18,0x04,0x10,0x08,0x04,0x10,0x08,0x04,0x10,0x08,0x07,0x18,0x10,0x03,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0xF8,0x06,0x07,0xF8,0x06,0x18,0x00,0x06,0xE0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x01,0xE1,0xE0,0x03,0xF7,0xF0,0x06,0x34,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x06,0x16,0x18,0x03,0xF3,0xF0,0x01,0xC1,0xE0,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0xF8,0x00,0x03,0xFC,0x30,0x03,0x06,0x38,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x04,0x10,0x03,0x08,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x1A,0x00,0x30,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x00,0x22,0x00,0x00,0x41,0x00,0x00,0x80,0x80,0x01,0x00,0x40,0x02,0x00,0x20,0x04,0x00,0x10,0x08,0x00,0x08,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x08,0x04,0x00,0x10,0x02,0x00,0x20,0x01,0x00,0x40,0x00,0x80,0x80,0x00,0x41,0x00,0x00,0x22,0x00,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x03,0xC0,0x00,0x04,0xC0,0x00,0x04,0x00,0x00,0x08,0x00,0x38,0x08,0x0F,0x38,0x08,0x08,0x38,0x08,0x10,0x00,0x0C,0x30,0x00,0x07,0xE0,0x00,0x03,0xC0,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x00,0xFF,0xE0,0x03,0x80,0x70,0x02,0x0F,0x10,0x06,0x70,0x88,0x04,0xC0,0x88,0x04,0x83,0x08,0x04,0x7F,0x88,0x02,0xC0,0x90,0x03,0x01,0x20,0x00,0xFE,0x40},/*"@",32*/
{0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x01,0xF8,0x00,0x3E,0x08,0x01,0xC2,0x00,0x07,0x02,0x00,0x07,0xE2,0x00,0x00,0xFE,0x00,0x00,0x1F,0xC8,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x00,0x08},/*"A",33*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x02,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x10,0x06,0x00,0x20,0x07,0x80,0xC0,0x00,0x00,0x00},/*"C",35*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x18,0x02,0x00,0x10,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"D",36*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x3E,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x01,0x00,0x60,0x00,0x00,0x00},/*"E",37*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x3E,0x00,0x06,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x02,0x03,0xF0,0x07,0x83,0xF0,0x00,0x02,0x00,0x00,0x02,0x00},/*"G",39*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x04,0x08,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x07,0x00,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x03,0x07,0xFF,0xFE,0x07,0xFF,0xFC,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00},/*"J",42*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x0C,0x08,0x00,0x18,0x00,0x00,0x3E,0x00,0x04,0xC7,0x80,0x05,0x03,0xC8,0x06,0x00,0xF8,0x04,0x00,0x38,0x04,0x00,0x18,0x00,0x00,0x08},/*"K",43*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x00},/*"L",44*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x80,0x08,0x07,0xFC,0x00,0x00,0x7F,0xC0,0x00,0x03,0xF8,0x00,0x07,0xC0,0x00,0x78,0x00,0x07,0x80,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"M",45*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x00,0x08,0x03,0xC0,0x00,0x00,0xE0,0x00,0x00,0x38,0x00,0x00,0x1E,0x00,0x00,0x07,0x00,0x00,0x01,0xC0,0x04,0x00,0xF0,0x07,0xFF,0xF8,0x04,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x00,0x30,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"O",47*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x04,0x08,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x06,0x0C,0x00,0x03,0xF8,0x00,0x01,0xF0,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x88,0x04,0x00,0x88,0x04,0x00,0xC8,0x06,0x00,0x3C,0x03,0x00,0x3E,0x01,0xFF,0xE6,0x00,0x7F,0x84,0x00,0x00,0x00},/*"Q",49*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x0C,0x00,0x04,0x0F,0x00,0x04,0x0B,0xC0,0x06,0x10,0xF0,0x03,0xF0,0x38,0x01,0xE0,0x08,0x00,0x00,0x08},/*"R",50*/
{0x00,0x00,0x00,0x01,0xE0,0xF8,0x03,0xF0,0x30,0x06,0x30,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x02,0x06,0x18,0x02,0x07,0xF0,0x07,0x81,0xE0,0x00,0x00,0x00},/*"S",51*/
{0x01,0x80,0x00,0x06,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x00,0x04,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00},/*"T",52*/
{0x04,0x00,0x00,0x07,0xFF,0xE0,0x07,0xFF,0xF0,0x04,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x04,0x00,0x10,0x07,0xFF,0xE0,0x04,0x00,0x00},/*"U",53*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0xE0,0x00,0x07,0xFE,0x00,0x04,0x1F,0xE0,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x01,0xE0,0x04,0x3E,0x00,0x07,0xC0,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"V",54*/
{0x04,0x00,0x00,0x07,0xE0,0x00,0x07,0xFF,0xC0,0x04,0x1F,0xF8,0x00,0x07,0xC0,0x07,0xF8,0x00,0x07,0xFF,0x80,0x04,0x3F,0xF8,0x00,0x07,0xC0,0x04,0xF8,0x00,0x07,0x00,0x00,0x04,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x06,0x00,0x18,0x07,0xC0,0x78,0x05,0xF1,0xC8,0x00,0x3E,0x00,0x00,0x1F,0x80,0x04,0x63,0xE8,0x07,0x80,0xF8,0x06,0x00,0x18,0x04,0x00,0x08,0x00,0x00,0x00},/*"X",56*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0x80,0x00,0x07,0xE0,0x08,0x04,0x7C,0x08,0x00,0x1F,0xF8,0x00,0x07,0xF8,0x00,0x18,0x08,0x04,0xE0,0x08,0x07,0x00,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x01,0x00,0x08,0x06,0x00,0x38,0x04,0x00,0xF8,0x04,0x03,0xE8,0x04,0x0F,0x08,0x04,0x7C,0x08,0x05,0xF0,0x08,0x07,0xC0,0x08,0x07,0x00,0x18,0x04,0x00,0x60,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xFF,0xFE,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x00,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x07,0x00,0x00,0x00,0xC0,0x00,0x00,0x38,0x00,0x00,0x06,0x00,0x00,0x01,0xC0,0x00,0x00,0x30,0x00,0x00,0x0E,0x00,0x00,0x01,0x00,0x00,0x00},/*"\",60*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x3F,0xFF,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x10,0x00,0x00,0x30,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01},/*"_",63*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x19,0xF8,0x00,0x1B,0x18,0x00,0x22,0x08,0x00,0x26,0x08,0x00,0x24,0x08,0x00,0x24,0x10,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x18},/*"a",65*/
{0x00,0x00,0x00,0x04,0x00,0x00,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x18,0x18,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x18,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x18,0x30,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3C,0x08,0x00,0x1C,0x10,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x04,0x10,0x10,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x12,0x30,0x00,0x22,0x18,0x00,0x22,0x08,0x00,0x22,0x08,0x00,0x32,0x08,0x00,0x1E,0x10,0x00,0x0E,0x20,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x01,0xFF,0xF8,0x03,0xFF,0xF8,0x06,0x20,0x08,0x04,0x20,0x08,0x04,0x20,0x08,0x07,0x20,0x00,0x03,0x00,0x00,0x00,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x0E,0x6E,0x00,0x1F,0xF3,0x00,0x31,0xB1,0x00,0x20,0xB1,0x00,0x20,0xB1,0x00,0x31,0x91,0x00,0x1F,0x13,0x00,0x2E,0x1E,0x00,0x20,0x0E,0x00,0x30,0x00},/*"g",71*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x06,0x3F,0xF8,0x06,0x3F,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x03,0x00,0x20,0x01,0x00,0x20,0x01,0x00,0x20,0x03,0x06,0x3F,0xFE,0x06,0x3F,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"j",74*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x88,0x00,0x03,0x00,0x00,0x2F,0xC0,0x00,0x38,0xF8,0x00,0x20,0x38,0x00,0x20,0x08,0x00,0x00,0x08,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x00,0x08},/*"m",77*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x10,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x0F,0xF0,0x00,0x18,0x30,0x00,0x30,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x08,0x00,0x18,0x30,0x00,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x20,0x01,0x00,0x3F,0xFF,0x00,0x3F,0xFF,0x00,0x10,0x11,0x00,0x20,0x09,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x38,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x09,0x00,0x10,0x11,0x00,0x1F,0xFF,0x00,0x3F,0xFF,0x00,0x00,0x01,0x00,0x00,0x00},/*"q",81*/
{0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x08,0x08,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x30,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x78,0x00,0x1E,0x18,0x00,0x33,0x08,0x00,0x23,0x08,0x00,0x21,0x08,0x00,0x21,0x88,0x00,0x21,0x98,0x00,0x30,0xF0,0x00,0x38,0x60,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0xFF,0xF0,0x03,0xFF,0xF8,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x3F,0xF0,0x00,0x7F,0xF8,0x00,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x20,0x10,0x00,0x3F,0xF8,0x00,0x7F,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x3C,0x00,0x00,0x3F,0x80,0x00,0x23,0xF0,0x00,0x00,0x78,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x30,0x00,0x00,0x20,0x00},/*"v",86*/
{0x00,0x20,0x00,0x00,0x3C,0x00,0x00,0x3F,0xE0,0x00,0x23,0xF8,0x00,0x00,0xE0,0x00,0x27,0x00,0x00,0x3E,0x00,0x00,0x3F,0xE0,0x00,0x21,0xF8,0x00,0x01,0xE0,0x00,0x3E,0x00,0x00,0x20,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x38,0x38,0x00,0x3E,0x68,0x00,0x27,0x80,0x00,0x03,0xC8,0x00,0x2C,0xF8,0x00,0x38,0x38,0x00,0x20,0x18,0x00,0x20,0x08,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x03,0x00,0x3C,0x01,0x00,0x3F,0x83,0x00,0x23,0xEC,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x08,0x00,0x20,0x38,0x00,0x20,0xF8,0x00,0x23,0xE8,0x00,0x2F,0x88,0x00,0x3E,0x08,0x00,0x38,0x08,0x00,0x20,0x18,0x00,0x00,0x70,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x1F,0xF7,0xFC,0x30,0x00,0x06,0x20,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x30,0x00,0x06,0x1F,0xF7,0xFC,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x0C,0x00,0x00,0x10,0x00,0x00},/*"~",94*/
};      
#endif

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.coloradmin.cn/o/431901.html

如若内容造成侵权/违法违规/事实不符，请联系多彩编程网进行投诉反馈，一经查实，立即删除！

相关文章

第一节 法学

第一节 法学

目录 法学的概念法学的性质 实践性构成了法学的学问性质 法学的研究对象 1.法律制度问题&#xff08;X法律制度&#xff09;2. 社会现实或社会生活关系问题 (Y社会现实/社会关系)3.法律制度与社会现实之间如何对应的问题 &#xff08;Yf(x) f为什么函数&#xff09; 法学的概…
阅读更多...
ChatGPT或要推出APP，OpenAI官宣为ChatGPT招募移动端开发工程师

ChatGPT或要推出APP，OpenAI官宣为ChatGPT招募移动端开发工程师

文 | 兔子酱OpenAI官方招聘页面放出了英雄帖&#xff0c;他们正在为ChatGPT招聘移动端工程师&#xff1a;传送门&#xff1a;https://openai.com/careers/mobile-engineering-manager-chatgpt其中&#xff0c;跨iOS和Android的工程主管年薪为20至37万美元,总薪酬还包括慷慨的股…
阅读更多...
ActiveMQ使用(五):在JavaScript中发送的MQTT消息在C#中变为字节数组

ActiveMQ使用(五):在JavaScript中发送的MQTT消息在C#中变为字节数组

ActiveMQ使用(五):在JavaScript中发送的MQTT消息在C#中变为字节数组 1. 问题描述 ** C#中的代码: ** internal class Program{static void Main(string[] args){ConnectionFactory factory new ConnectionFactory("tcp://localhost:61616");IConnection connecti…
阅读更多...
【数据结构与算法】程序员常用10种算法（分治算法）

【数据结构与算法】程序员常用10种算法（分治算法）

一、分治算法介绍 在计算机科学中&#xff0c;分治法就是运用分治思想的一种很重要的算法。 分治&#xff0c;字面上的解释是“分而治之”&#xff0c;就是把一个复杂的问题分成两个或更多的相同或相似的子问题&#xff0c;再把子问题分成更小的子问题……直到最后子问题可以…
阅读更多...
【DNS】域名解析服务

【DNS】域名解析服务

文章目录 1.DNS1.1 DNS定义1.2 DNS系统作用1.3 DNS解析过程 1.DNS 1.1 DNS定义 DNS是"域名系统"的英文缩写。它作为将域名和IP地址相互映射的一个分布式数据库&#xff0c;能够使人更方便地访问互联网。 DNS服务使用TCP和UDP的53端口&#xff0c;TCP的53端口用于连…
阅读更多...
Java - 内部类

Java - 内部类

1、本地内部类 2、实例内部类 3、静态内部类 4、匿名内部类 首先&#xff0c;我要在这声明一下&#xff0c;内部类也是类&#xff0c;不管它是属于何种类型。 只要是类&#xff0c;就会有类的特性&#xff1a;继承 / 被继承&#xff0c;实现接口&#xff0c;套娃【内部类再套一…
阅读更多...
JWT 鉴权插件上线！让你的 API 更安全！

JWT 鉴权插件上线！让你的 API 更安全！

API鉴权是保证API安全性和可用性的一项重要措施。通过API鉴权&#xff0c;系统可以对用户或者应用进行有效的身份认证和权限管理。 除了我们之前更新的 Basic Auth 鉴权插件&#xff0c;这次给大家带来 JWT 鉴权插件。 JSON Web Token是一种开放标准&#xff0c;可以让服务器生…
阅读更多...
数字孪生智慧路桥怎么实现?

数字孪生智慧路桥怎么实现?

近年来&#xff0c;道路桥梁安全事故频发&#xff0c;直接影响到了行车人员的人身安全&#xff0c;并且对整个公路桥梁的稳定性产生了不良影响。因此对道路桥梁运行状态的实时监测、及时进行运行状态的预警、实现巡检运维智慧化&#xff0c;已成为桥梁道路管理重点关注的方面。…
阅读更多...
PostgreSQL与MySQL优劣势比较浅谈

PostgreSQL与MySQL优劣势比较浅谈

目录 1 简介2 postgresql比mysql强大在那些方面3 PostgreSQL 为什么在国内没有MySQL流行4 postgresql比mysql一些主要区别5 postgresql比mysql特征比较5.1 MariaDB的主要特点5.2 PostgreSQL的主要特点 6 总结 1 简介 因为公司使用PostgreSQL很长时间了&#xff0c;忙于功能开发…
阅读更多...
计算机视觉-角点检测

计算机视觉-角点检测

角点检测 1.分别实现Harris角点检测与SIFT特征提取&#xff0c;对比两者的区别1.1代码实现1.2两者区别 2.利用SIFT算法实现两幅相近图像的特征匹配2.1代码实现 3.实现匹配地理标记图像3.1代码实现 4.实验注意事项4.1实验需要安装的库和应用4.2报错内容 5.小结 1.分别实现Harris…
阅读更多...
cdr文件怎么转化成ai文件 CDR文件转AI文件大小会变化吗

cdr文件怎么转化成ai文件 CDR文件转AI文件大小会变化吗

cdr与AI软件都可以用于制作矢量图形。基于不同的打印与使用需求&#xff0c;可能需要将cdr文件保存为ai文件使用。那么&#xff0c;cdr文件怎么转化成ai文件&#xff0c;CDR文件转AI文件大小会变化吗&#xff1f;下面让我们来详细解读一下吧。 一、cdr文件怎么转化成ai文件 c…
阅读更多...
实验7 回归问题

实验7 回归问题

1. 实验目的 ①掌握一元线性回归模型的实现方法&#xff1b; ②掌握多元线性回归模型的实现方法&#xff1b; ③掌握三维数据可视化方法。 2. 实验内容 ①使用TensorFlow建立一元线性回归模型&#xff0c;使用商品房销售数据训练模型&#xff0c;并使用训练好的模型预测房价…
阅读更多...
【C++】17.map和set的模拟实现

【C++】17.map和set的模拟实现

1.红黑树中的迭代器 operator是关键 迭代需要走中序 如何走中序? _node从左子树的最左结点开始遍历走中序 分两类情况: 如果右树不为空 那么中序的下一个就是右子树的最左结点 如果右树为空 那么表示_node所在的子树已经完成 在一个结点的祖先去找 沿着路径往上孩子是它的…
阅读更多...
【Linux】网络基础（网络层与链路层）

【Linux】网络基础（网络层与链路层）

网络层与链路层典型协议网络层IP 地址地址管理网络号的划分&#xff08;五种&#xff09;特殊的网络以及IP地址路由选择链路层MAC 地址ARP 协议MTU 最大传输单元其他典型协议&#xff1a;ICMP、DNS 、NAT技术ICMP协议DNS 协议NAT & NAPT 技术代理网络层 功能&#xff1a;负…
阅读更多...
算法设计与分析阶段考总结

算法设计与分析阶段考总结

前言&#xff1a;基本是为了我自己看的一些我容易忘记的东西&#xff0c;为考试作准备把 第一章 算法中的基本概念 程序设计数据结构算法 算法特性 1.有穷性 2.确定性 3.可行性 4.输出 5.输入 算法复杂性分析 算法复杂性依赖于&#xff1a;问题规模N&#xff0c;输入I&#xff…
阅读更多...
TCP 的可靠传输

TCP 的可靠传输

目录 可靠传输有啥用确认应答超时重传总结 可靠传输有啥用 我们知道相比于 UDP, TCP 的传输是可靠的, 啥意思呢? 就是 UDP 发送的数据, 它自己不知道发送的数据对方是否接收到. 而 TCP 发送的数据, 它知道对方是否接收到, 也就是说对方会给个应答. 假设一个场景 : 甲要付款给…
阅读更多...
全网最详细，Jmeter性能测试-性能基础详解，接口关联与编写Java脚本（三）

全网最详细，Jmeter性能测试-性能基础详解，接口关联与编写Java脚本（三）

目录&#xff1a;导读前言一、Python编程入门到精通二、接口自动化项目实战三、Web自动化项目实战四、App自动化项目实战五、一线大厂简历六、测试开发DevOps体系七、常用自动化测试工具八、JMeter性能测试九、总结&#xff08;尾部小惊喜&#xff09;前言 接口关联 接口关联…
阅读更多...
Vector - CAPL - CAN x 总线信息获取（续1）

Vector - CAPL - CAN x 总线信息获取（续1）

继续.... 目录 OverLoadFrameCount -- 过载帧数量 代码示例 OverLoadFrameRate -- 过载帧速率 代码示例 StandardFrameCount -- 标准帧数量 代码示例 StandardFrameRate -- 标准帧速率 代码示例 StandardRemoteFrameCount -- 标准远程帧数量 代码示例 StandardRemote…
阅读更多...
Java注解编译期处理AbstractProcessor详解

Java注解编译期处理AbstractProcessor详解

文章目录概述注解处理器注解处理流程AbstractProcessorgetSupportedOptions()getSupportedAnnotationTypesgetSupportedSourceVersioninit初始化process 处理方法如何注册注解处理器如何调试编译期代码Maven相关配置(指定生效的Processor)注意事项自定义注解处理器范例范例一&a…
阅读更多...
多线程小知识

多线程小知识

多线程 多线程环境使用哈希表HashMapHashtableConcurrentHashMap 死锁死锁是什么两者之间的死锁多人之间的死锁 死锁产生的四个必要条件:互斥使用不可抢占请求和保持循环等待 不同的锁ReentrantLockSynchronized和ReentrantLock之间的区别:具体选择Synchronized加锁工作过程偏向…
阅读更多...
推荐文章
最新文章

Copyright @ 2022~2023