华为配置旁挂二层组网直接转发示例

配置旁挂二层组网直接转发示例

组网图形

图1 配置旁挂二层组网直接转发示例组网图

业务需求
组网需求
数据规划
配置思路
配置注意事项
操作步骤
配置文件
扩展阅读

业务需求

企业用户通过WLAN接入网络，以满足移动办公的最基本需求。且在覆盖区域内移动发生漫游时，不影响用户的业务使用。

组网需求

AC组网方式：旁挂二层组网。
DHCP部署方式：
- AC作为DHCP服务器为AP分配IP地址。
- 汇聚交换机SwitchB作为DHCP服务器为STA分配IP地址。
业务数据转发方式：直接转发。

数据规划

表1 AC数据规划表
配置项	数据
AP管理VLAN	VLAN100
STA业务VLAN	VLAN101
DHCP服务器	AC作为DHCP服务器为AP分配IP地址汇聚交换机SwitchB作为DHCP服务器为STA分配IP地址，STA的默认网关为10.23.101.2
AP的IP地址池	10.23.100.2～10.23.100.254/24
STA的IP地址池	10.23.101.3～10.23.101.254/24
AC的源接口IP地址	VLANIF100：10.23.100.1/24
AP组	名称：ap-group1 引用模板：VAP模板wlan-net、域管理模板default
域管理模板	名称：default 国家码：中国
SSID模板	名称：wlan-net SSID名称：wlan-net
安全模板	名称：wlan-net 安全策略：WPA-WPA2+PSK+AES 密码：a1234567
VAP模板	名称：wlan-net 转发模式：直接转发业务VLAN：VLAN101 引用模板：SSID模板wlan-net、安全模板wlan-net

配置思路

配置AP、AC和周边网络设备之间实现网络互通。
配置AP上线。
1. 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。
2. 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。
3. 配置AP上线的认证方式并离线导入AP，实现AP正常上线。
配置WLAN业务参数，实现STA访问WLAN网络功能。

配置注意事项

纯组播报文由于协议要求在无线空口没有ACK机制保障，且无线空口链路不稳定，为了纯组播报文能够稳定发送，通常会以低速报文形式发送。如果网络侧有大量异常组播流量涌入，则会造成无线空口拥堵。为了减小大量低速组播报文对无线网络造成的冲击，建议配置组播报文抑制功能。配置前请确认是否有组播业务，如果有，请谨慎配置限速值。
- 业务数据转发方式采用直接转发时，建议在直连AP的交换机接口上配置组播报文抑制。
- 业务数据转发方式采用隧道转发时，建议在AC的流量模板下配置组播报文抑制。
建议在与AP直连的设备接口上配置端口隔离，如果不配置端口隔离，尤其是业务数据转发方式采用直接转发时，可能会在VLAN内形成大量不必要的广播报文，导致网络阻塞，影响用户体验。
隧道转发模式下，管理VLAN和业务VLAN不能配置为同一VLAN，且AP和AC之间只能放通管理VLAN，不能放通业务VLAN。
V200R021C00版本开始，配置CAPWAP源接口或源地址时，会检查和安全相关的配置是否已存在，包括DTLS加密的PSK、AC间DTLS加密的PSK、登录AP的用户名和密码、全局离线管理VAP的登录密码，均已存在才能成功配置，否则会提示用户先完成相关的配置。
V200R021C00版本开始，AC默认开启CAPWAP控制隧道的DTLS加密功能。开启该功能，添加AP时AP会上线失败，此时需要先开启CAPWAP DTLS不认证方式（capwap dtls no-auth enable）让AP上线，以便AP获取安全凭证，AP上线后应及时关闭该功能（undo capwap dtls no-auth enable），避免未授权AP上线。

操作步骤

配置周边设备

# 配置接入交换机SwitchA的GE0/0/1和GE0/0/2接口加入VLAN100和VLAN101，GE0/0/1的缺省VLAN为VLAN100。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1192280004190921">system-view</strong>
[HUAWEI] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1222166240190921">sysname SwitchA</strong>
[SwitchA] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1183461715190921">vlan batch 100 101</strong>
[SwitchA] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1005154605190921">interface gigabitethernet 0/0/1</strong>
[SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1349582656190921">port link-type trunk</strong>
[SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b636724399190921">port trunk pvid vlan 100</strong>
[SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b103409417190921">port trunk allow-pass vlan 100 101</strong>
[SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b896559407190921">port-isolate enable</strong>
[SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b951942244190921">quit</strong>
[SwitchA] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2123180437190921">interface gigabitethernet 0/0/2</strong>
[SwitchA-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1745410152190921">port link-type trunk</strong>
[SwitchA-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1787123792190921">port trunk allow-pass vlan 100 101</strong>
[SwitchA-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1239957325190921">quit</strong></span></span></span>

# 配置汇聚交换机SwitchB的接口GE0/0/1加入VLAN100和VLAN101，接口GE0/0/2加入VLAN100，GE0/0/3加入VLAN101。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1674717277190921">system-view</strong>
[HUAWEI] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1445629532190921">sysname SwitchB</strong>
[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b647498740190921">vlan batch 100 101</strong>
[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b125795402190921">interface gigabitethernet 0/0/1</strong>
[SwitchB-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b877541276190921">port link-type trunk</strong>
[SwitchB-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b707960753190921">port trunk allow-pass vlan 100 101</strong>
[SwitchB-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1228466072190921">quit</strong>
[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b298987462190921">interface gigabitethernet 0/0/2</strong>
[SwitchB-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b864863078190921">port link-type trunk</strong>
[SwitchB-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1730539876190921">port trunk allow-pass vlan 100</strong>
[SwitchB-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2079017324190921">quit</strong>
[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2040272214190921">interface gigabitethernet 0/0/3</strong>
[SwitchB-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b602819935190921">port link-type trunk</strong>
[SwitchB-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b916832533190921">port trunk allow-pass vlan 101</strong>
[SwitchB-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1666471945190921">quit</strong></span></span></span>

# 配置Router的接口GE1/0/0加入VLAN101，创建接口VLANIF101并配置IP地址为10.23.101.2/24。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd"><Huawei> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b118005268190921">system-view</strong>
[Huawei] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1176501588190921">sysname Router</strong>
[Router] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b995805857190921">vlan batch 101</strong>
[Router] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b906637926190921">interface gigabitethernet 1/0/0</strong>
[Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b406876624190921">port link-type trunk</strong>
[Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1226529678190921">port trunk allow-pass vlan 101</strong>
[Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1131638750190921">quit</strong>
[Router] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b648829236190921">interface vlanif 101</strong>
[Router-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1969966747190921">ip address 10.23.101.2 24</strong>
[Router-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1246477905190921">quit</strong></span></span></span>

配置AC与其它网络设备互通

如果AC直接连接AP，需要在AC直连AP的接口上配置缺省VLAN为管理VLAN100。

# 配置AC的接口GE0/0/1加入VLAN100。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1248097008190921">system-view</strong>
[HUAWEI] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2092838922190921">sysname AC</strong>
[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2061833437190921">vlan batch 100 101</strong>
[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1024087155190921">interface gigabitethernet 0/0/1</strong>
[AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b380448131190921">port link-type trunk</strong>
[AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1570869377190921">port trunk allow-pass vlan 100</strong>
[AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b686476124190921">quit</strong></span></span></span>

配置DHCP服务器为STA和AP分配IP地址

# 在AC上配置VLANIF100接口为AP提供IP地址。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b270083456190921">dhcp enable</strong>
[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1697431376190921">interface vlanif 100</strong>
[AC-Vlanif100] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1645914341190921">ip address 10.23.100.1 24</strong>
[AC-Vlanif100] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b2011614048190921">dhcp select interface</strong>
[AC-Vlanif100] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1870662344190921">quit</strong></span></span></span>

# 在SwitchB上配置VLANIF101接口为STA提供IP地址，并指定10.23.101.2作为STA的默认网关地址。

DNS服务器地址请根据实际需要配置。常用配置方法如下：

接口地址池场景，需要在VLANIF接口视图下执行命令dhcp server dns-list ip-address &<1-8>。
全局地址池场景，需要在IP地址池视图下执行命令dns-list ip-address &<1-8>。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1746102230190921">dhcp enable</strong>
[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b181711504190921">interface vlanif 101</strong>
[SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1130572979190921">ip address 10.23.101.1 24</strong>
[SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b133774347190921">dhcp select interface</strong>
[SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1216259955190921">dhcp server gateway-list 10.23.101.2</strong>
[SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b366557450190921">quit</strong></span></span></span>

配置AP上线

# 创建AP组，用于将相同配置的AP都加入同一AP组中。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1451837292190921">wlan</strong>
[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1710308668190921">ap-group name ap-group1</strong>
[AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b294415960190921">quit</strong></span></span></span>

# 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1815954045190921">regulatory-domain-profile name default</strong>
[AC-wlan-regulate-domain-default] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1765454957190921">country-code cn</strong>
[AC-wlan-regulate-domain-default] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b464951690190921">quit</strong>
[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1132959133190921">ap-group name ap-group1</strong>
[AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b4510754102210">regulatory-domain-profile default</strong>
Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continue?[Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_zh-cn_task_0175818418_b17491131153716">y</strong>  
[AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b101836067190921">quit</strong>
[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b465166413190921">quit</strong></span></span></span>

# 配置AC的源接口。

V200R021C00版本开始，配置CAPWAP源接口或源地址时，会检查和安全相关的配置是否已存在，包括DTLS加密的PSK、AC间DTLS加密的PSK、登录AP的用户名和密码、全局离线管理VAP的登录密码，均已存在才能成功配置，否则会提示用户先完成相关的配置。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b806281647190921">capwap source interface vlanif 100</strong>
Set the DTLS PSK(contains 6-32 plain-text characters, or 48 or 68 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):******

Set the DTLS inter-controller PSK(contains 6-32 plain-text characters, or 48 or 68 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):******

Set the user name for FIT APs(contains 4-31 plain-text characters, which can only include letters, digits and underlines. And the first character must be a letter):admin

Set the password for FIT APs(plain-text password of 8-128 characters or cipher-text password of 48-188 characters that must be a combination of at least three of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):********

Set the global temporary-management psk(contains 8-63 plain-text characters, or 48-108 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):********</span></span></span>

# 开启CAPWAP DTLS不认证方式。（V200R021C00及之后版本）

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b15163144818377">capwap dtls no-auth enable</strong></span></span></span>

V200R021C00版本开始，AC默认开启CAPWAP控制隧道的DTLS加密功能。开启该功能，添加AP时AP会上线失败，此时需要先开启CAPWAP DTLS不认证方式让AP上线，以便AP获取安全凭证，AP上线后应及时关闭该功能，避免未授权AP上线。

# 在AC上离线导入AP，并将AP加入AP组“ap-group1”中。假设AP的MAC地址为60de-4476-e360，并且根据AP的部署位置为AP配置名称，便于从名称上就能够了解AP的部署位置。例如MAC地址为60de-4476-e360的AP部署在1号区域，命名此AP为area_1。

ap auth-mode命令缺省情况下为MAC认证，如果之前没有修改其缺省配置，可以不用执行ap auth-mode mac-auth。

举例中使用的AP为AP5030DN，具有射频0和射频1两个射频。AP5030DN的射频0为2.4GHz射频，射频1为5GHz射频。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b763711121190921">wlan</strong>
[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1389711844190921">ap auth-mode mac-auth</strong>
[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1382708357190921">ap-id 0 ap-mac 60de-4476-e360</strong>
[AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1272920990190921">ap-name area_1</strong>
Warning: This operation may cause AP reset. Continue? [Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_zh-cn_task_0175818418_b460951517190906">y</strong>  
[AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b614746147190921">ap-group ap-group1</strong>
Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_zh-cn_task_0175818418_b1651706244190906">y</strong>  
[AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b959850628190921">quit</strong></span></span></span>

# 将AP上电后，当执行命令display ap all查看到AP的“State”字段为“nor”时，表示AP正常上线。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b482061123190921">display ap all</strong>
Total AP information:
nor  : normal          [1]
Extra information:
P  : insufficient power supply
--------------------------------------------------------------------------------------------------
ID   MAC            Name   Group     IP            Type            State STA Uptime      ExtraInfo
--------------------------------------------------------------------------------------------------
0    60de-4476-e360 area_1 ap-group1 10.23.100.254 AP5030DN        nor   0   10S         -
--------------------------------------------------------------------------------------------------
Total: 1</span></span></span>

# 关闭CAPWAP DTLS不认证方式。（V200R021C00及之后版本）

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b3420155514467">quit</strong>
[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1898583494615">undo capwap dtls no-auth enable</strong>
[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b9381917104714">wlan</strong></span></span></span>

配置WLAN业务参数

# 创建名为“wlan-net”的安全模板，并配置安全策略。

举例中以配置WPA-WPA2+PSK+AES的安全策略为例，密码为“a1234567”，实际配置中请根据实际情况，配置符合实际要求的安全策略。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1991067776190921">security-profile name wlan-net</strong>
[AC-wlan-sec-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b851752672190921">security wpa-wpa2 psk pass-phrase a1234567 aes</strong>
[AC-wlan-sec-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b337241812190921">quit</strong></span></span></span>

# 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b69022931190921">ssid-profile name wlan-net</strong>
[AC-wlan-ssid-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b36723145190921">ssid wlan-net</strong>
[AC-wlan-ssid-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1738903244190921">quit</strong></span></span></span>

# 创建名为“wlan-net”的VAP模板，配置业务数据转发模式、业务VLAN，并且引用安全模板和SSID模板。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1964707822190921">vap-profile name wlan-net</strong>
[AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1849868164190921">forward-mode direct-forward</strong>
[AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b166547162190921">service-vlan vlan-id 101</strong>
[AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b7899292190921">security-profile wlan-net</strong>
[AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b164868007190921">ssid-profile wlan-net</strong>
[AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1178727990190921">quit</strong></span></span></span>

# 配置AP组引用VAP模板，AP上射频0和射频1都使用VAP模板“wlan-net”的配置。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b2051092768190921">ap-group name ap-group1</strong>
[AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1753511747190921">vap-profile wlan-net wlan 1 radio 0</strong>
[AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1212706755190921">vap-profile wlan-net wlan 1 radio 1</strong>
[AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b729861449190921">quit</strong></span></span></span>

配置AP射频的信道和功率

射频的信道和功率自动调优功能默认开启，如果不关闭此功能则会导致手动配置不生效。举例中AP射频的信道和功率仅为示例，实际配置中请根据AP的国家码和网规结果进行配置。

# 关闭AP射频0的信道和功率自动调优功能，并配置AP射频0的信道和功率。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1423607009190921">ap-id 0</strong>
[AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1534489953190921">radio 0</strong>
[AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b733594144190921">calibrate auto-channel-select disable</strong>
[AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1154293079190921">calibrate auto-txpower-select disable</strong>
[AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1858200296190921">channel 20mhz 6</strong>
Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_zh-cn_task_0175818418_b1384307436190906">y</strong> 
[AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b554899294190921">eirp 127</strong>
[AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1779547689190921">quit</strong></span></span></span>

# 关闭AP射频1的信道和功率自动调优功能，并配置AP射频1的信道和功率。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b33229250190921">radio 1</strong>
[AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b327597144190921">calibrate auto-channel-select disable</strong>
[AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1164564697190921">calibrate auto-txpower-select disable</strong>
[AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b201103780190921">channel 20mhz 149</strong>
Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_zh-cn_task_0175818418_b1384307436190906_1">y</strong> 
[AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b652286665190921">eirp 127</strong>
[AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1440636620190921">quit</strong>
[AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b904227301190921">quit</strong></span></span></span>

验证配置结果

WLAN业务配置会自动下发给AP，配置完成后，通过执行命令display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP对应的射频上的VAP已创建成功。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b367333496190921">display vap ssid wlan-net</strong>
WID : WLAN ID
--------------------------------------------------------------------------------
AP ID AP name RfID WID   BSSID          Status  Auth type     STA   SSID
--------------------------------------------------------------------------------
0     area_1  0    1     60DE-4476-E360 <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1874482883190921">ON</strong>      WPA/WPA2-PSK  0     wlan-net
0     area_1  1    1     60DE-4476-E370 <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1628414885190921">ON</strong>      WPA/WPA2-PSK  0     wlan-net
-------------------------------------------------------------------------------
Total: 2</span></span></span>

STA搜索到名为“wlan-net”的无线网络，输入密码“a1234567”并正常关联后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线网络“wlan-net”中。

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1120837202190921">display station ssid wlan-net</strong>
Rf/WLAN: Radio ID/WLAN ID
Rx/Tx: link receive rate/link transmit rate(Mbps)
---------------------------------------------------------------------------------
STA MAC         AP ID Ap name   Rf/WLAN  Band  Type  Rx/Tx      RSSI  VLAN  IP address
---------------------------------------------------------------------------------
e019-1dc7-1e08  0     area_1    1/1      5G    11n   46/59      -68   101   10.23.101.254
---------------------------------------------------------------------------------
Total: 1 2.4G: 0 5G: 1</span></span></span>

配置文件

SwitchA的配置文件

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">#
sysname SwitchA
#
vlan batch 100 to 101
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk pvid vlan 100
 port trunk allow-pass vlan 100 to 101
 port-isolate enable group 1
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 100 to 101
#
return</span></span></span>

SwitchB的配置文件

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">#
sysname SwitchB
#
vlan batch 100 to 101
#
dhcp enable
#
interface Vlanif101
 ip address 10.23.101.1 255.255.255.0
 dhcp select interface
 dhcp server gateway-list 10.23.101.2
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 100 to 101
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 100
#
interface GigabitEthernet0/0/3
 port link-type trunk
 port trunk allow-pass vlan 101
#
return</span></span></span>

Router的配置文件

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">#
sysname Router
#
vlan batch 101
#
interface Vlanif101
 ip address 10.23.101.2 255.255.255.0
#
interface GigabitEthernet1/0/0
 port link-type trunk
 port trunk allow-pass vlan 101
#
return
</span></span></span>

AC的配置文件

<span style="color:#333333"><span style="background-color:#ffffff"><span style="background-color:#dddddd">#
 sysname AC
#
vlan batch 100 to 101
#
dhcp enable
#
interface Vlanif100
 ip address 10.23.100.1 255.255.255.0
 dhcp select interface
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 100
#
capwap source interface vlanif100
#
wlan
 security-profile name wlan-net
  security wpa-wpa2 psk pass-phrase %^%#m"tz0f>~7.[`^6RWdzwCy16hJj/Mc!,}s`X*B]}A%^%# aes
 ssid-profile name wlan-net
  ssid wlan-net
 vap-profile name wlan-net
  service-vlan vlan-id 101
  ssid-profile wlan-net
  security-profile wlan-net
 regulatory-domain-profile name default
 ap-group name ap-group1
  radio 0
   vap-profile wlan-net wlan 1
  radio 1
   vap-profile wlan-net wlan 1
 ap-id 0 type-id 35 ap-mac 60de-4476-e360 ap-sn 210235554710CB000042
  ap-name area_1
  ap-group ap-group1
  radio 0
   channel 20mhz 6
   eirp 127
   calibrate auto-channel-select disable 
   calibrate auto-txpower-select disable
  radio 1
   channel 20mhz 149
   eirp 127
   calibrate auto-channel-select disable 
   calibrate auto-txpower-select disable
#
return</span></span></span>