【TI毫米波雷达】LP87702/LP87524电源PMIC芯片的BUCK供电配置

文章目录

上电时序
LP87702/LP87524电源芯片配置流程
- LP87702/LP87524开始运行
- - LP87702/LP87524 首次启动：
  - LP87702/LP87524 非首次启动：
- LP87702初始化
- LP87524初始化
- 代码例程
附录：结构框架
- 雷达基本原理叙述
- 雷达天线排列位置
- 芯片框架
- Demo工程功能
- CCS工程导入
- 工程叙述
- - Software Tasks
  - Data Path
  - Output information sent to host
  - - List of detected objects
    - Range profile
    - Azimuth static heatmap
    - Azimuth/Elevation static heatmap
    - Range/Doppler heatmap
    - Stats information
    - Side information of detected objects
    - Temperature Stats
    - Range Bias and Rx Channel Gain/Phase Measurement and Compensation
    - Streaming data over LVDS
    - Implementation Notes
    - How to bypass CLI
    - Hardware Resource Allocation

上电时序

由IWR6843硬件手册可以看到几路供电的上电时序
在这里插入图片描述

LP87702/LP87524电源芯片配置流程

LP8752x-Q1 10-A Buck Converter With Integrated Switche
具有诊断功能的 LP87702-Q1 双路降压转换器和 5V 升压转换器

LP87702/LP87524从机地址都是0x60
LP87702/LP87524中的设备ID等寄存器，是根据OTP EPROM来确定的，每一个芯片其设备ID都不同，通过判断是否首次启动来进行不同的操作。
PWM和PFM两种工作模式：前者驱动电流更大，600mA或更大负载下用PWM。强制使用PWM模式时，若负载小，则会自动切换到PFM模式。配置相应寄存器可以控制，建议选择自动模式。

LP87702/LP87524开始运行

使能VCC_5V，（ENABLE_VCC_5V），VCC_5V_EN引脚输出高电平，EN_LP87702输出高电平（最好是延迟4ms后再延迟4ms）
根据EEPROM中的某一区域标志位判断LP87702/LP87524是否是首次启动（也可通过I2C_Judge函数来判断设备是否正常，则可忽略这一步骤）：

LP87702/LP87524 首次启动：

①软件复位：LP87524 0x18和LP87702 0x1F写入0x01延迟10ms
②读取设备ID寄存器，写入到EEPROM对应部分，对应启动标志位置1

LP87702/LP87524 非首次启动：

①软件复位：LP87524 0x18和LP87702 0x1F写入0x01延迟10ms
②读取EEPROM的设备ID存储部分，读取设备ID寄存器，两者相同则向下进行，否则报错
3. 执行初始化

LP87702初始化

在这里插入图片描述

将0x00写入LP87702_CONFIG，不选择下拉，此寄存器也可配置信号延时
配置以下寄存器，使CLKIN引脚用作控制看门狗的开启/禁用
#define LP87702_WD_DIS_CTRL_CODE 0x34 连续写入0x87，0x65，0x1B解锁
#define LP87702_WD_DIS_CONTROL 0x35 写入0x01
看门狗配置寄存器为0x1C-0x1E
配置WD_CTRL_2寄存器，可以设置WD_RESET输出方式和有效电平，Bit2默认为0表示WDI无下拉，写入0x00改为推挽输出
3. 依次配置以下寄存器，使B0输出1.8V，B1输出1.0V，BOOST输出5V：
#define LP87702_BUCK0_CTRL_1 0x02 默认0x08
#define LP87702_BUCK0_CTRL_2 0x03 默认0x1A
#define LP87702_BUCK1_CTRL_1 0x04 默认0x08
#define LP87702_BUCK1_CTRL_2 0x05 默认0x1A

#define LP87702_BUCK0_VOUT 0x06 写入0xB1
#define LP87702_BUCK1_VOUT 0x07 写入0x4D

#define LP87702_BOOST_CTRL 0x08 写入0x58
若需要延迟开启或关闭，则配置DEALY寄存器
若需启用电压监测，则配置PGOOD寄存器
最后一步再开启电压输出：
BUCK0_CTRL_1 先读取再写入使bit0置1
BUCK1_CTRL_1 先读取再写入使bit0置1
BOOST_CTRL 先读取再写入使bit0置1
4. 若有需要，可编程GPO引脚可以通过配置寄存器来输出高低电平。监测启用时，配置PG_CTRL寄存器可以使GPO用于监测输出。中断及状态在INT和STATUS寄存器内，中断屏蔽配置在MASK寄存器内。SEL_I_LOAD寄存器可开启电流测量。BOOST_ILIM_CTRL寄存器用于配置电流限度。

LP87524初始化

在这里插入图片描述

将0x40写入LP87524_CONFIG，CLKIN下拉，其他不选择下拉，此寄存器也可配置信号延时
将0x00写入PIN_FUNCTION寄存器，使其不使用GPIO功能
依次配置以下寄存器，使B0输出3.3V，B1输出1.8V，B2输出1.2V，B3输出1.0V
#define LP87524_BUCK0_CTRL1 0x02 写入0x34，bit7控制开启
#define LP87524_BUCK1_CTRL1 0x04 写入0x44，bit7和EN1控制开启
#define LP87524_BUCK2_CTRL1 0x06 写入0x54，bit7和EN2控制开启
#define LP87524_BUCK3_CTRL1 0x08 写入0x64，bit7和EN3控制开启

#define LP87524_BUCK0_VOUT 0x0A 写入0xFC
#define LP87524_BUCK0_FLOOR_VOUT 0x0B 写入0xFC
#define LP87524_BUCK1_VOUT 0x0C 写入0xB1
#define LP87524_BUCK1_FLOOR_VOUT 0x0D 写入0xB1
#define LP87524_BUCK2_VOUT 0x0E 写入0x75
#define LP87524_BUCK2_FLOOR_VOUT 0x0F 写入0x75
#define LP87524_BUCK3_VOUT 0x10 写入0x4D
#define LP87524_BUCK3_FLOOR_VOUT 0x11 写入0x4D
若需要延迟开启或关闭，则配置DEALY寄存器
若需启用电压监测，则配置PGOOD寄存器
最后一步再开启电压输出：
BUCK0_CTRL1 先读取再写入，使bit7置1
BUCK1_CTRL1 先读取再写入，使bit7置1，EN1输出高电平
BUCK2_CTRL1 先读取再写入，使bit7置1，EN2输出高电平
BUCK3_CTRL1 先读取再写入，使bit7置1，EN3输出高电平
3. 若有需要，可使能EN的GPIO复用功能，编程引脚可以通过配置寄存器来输出高低电平。中断及状态在INT和STAT寄存器内，中断屏蔽配置在MASK寄存器内。SEL_I_LOAD寄存器可开启电流测量。

代码例程

/*!
 * @brief       	使能LP87702_WDI引脚的定时器，开启定时器中断和PWM，并设置占空比为50
 *
 * @param 				None
 *
 * @return				None
 */
void Enable_LP87702_WDI_TIM(void)
{
	HAL_TIM_Base_Start_IT(&htim3);
	HAL_TIM_PWM_Start(&htim3,TIM_CHANNEL_4);
	__HAL_TIM_SetCompare(&htim3,TIM_CHANNEL_4,50);
}

/*!
 * @brief       	复位LP87702
 *
 * @param 				None
 *
 * @return				false/true: 错误/正确标志
 */
bool Reset_LP87702(void)
{
	uint8_t dat=0;
	dat=0x01;
	if(I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_RESET,1,&dat,1,true)!=true)
	{
		return false;
	}
	delay_ms(10);
	return true;
}

/*!
 * @brief       	控制LP87702的BUCK输出值
 *
 * @param 	[in]	buck_flag: BUCK序号，为2时控制所有
 *					[in]	voltage: 要输出的电压值
 *					[in]	WriteNotRead: 写入或读取
 *
 * @return				voltage_v: 写入或读取的电压值，控制所有时，写入的都为3.3V，读取的为两个电压值之和
 */
float Ctrl_LP87702_BUCK_VOUT(uint8_t buck_flag,float voltage_v,bool WriteNotRead)
{
	uint8_t dat=0;
	uint8_t add=0;	
	
	if(buck_flag>=2)
	{
		voltage_v=Ctrl_LP87702_BUCK_VOUT(0,3.3,WriteNotRead)+Ctrl_LP87702_BUCK_VOUT(1,3.3,WriteNotRead);
	}
	else
	{
		add = LP87702_BUCK0_VOUT+buck_flag;
		if(WriteNotRead)
		{
			
			if(voltage_v>=0.7f && voltage_v<=0.73f)
			{
				dat=0x14+(voltage_v-0.7f)/0.01f;
			}
			else if(voltage_v>0.73f && voltage_v<=1.4f)
			{
				dat=0x17+(voltage_v-0.73f)/0.005f;
			}
			else if(voltage_v>1.4f && voltage_v<=3.36f)
			{
				dat=0x9D+(voltage_v-1.4f)/0.02f;
			}
			else
			{
				dat=0;
			}
			
			I2C_Write_x(&hi2c2,LP87702_Slave_Add,add,1,&dat,1,true);
		}
		else
		{
			dat=I2C_Read_y(&hi2c2,LP87702_Slave_Add,add,1,1,true);	
			
			if(dat>=0x14 && dat<=0x17)
			{
				voltage_v=(dat-0x14)*0.01f+0.7f;
			}
			else if(dat>0x17 && dat<=0x9D)
			{
				voltage_v=(dat-0x17)*0.005f+0.73f;
			}
			else if(dat>=0x9D && dat<=0xFF)
			{
				voltage_v=(dat-0x9D)*0.02f+1.4f;
			}
			else
			{
				voltage_v=0;
			}
		}
	}	
	
	return voltage_v;
}

/*!
 * @brief       	开启LP87702的BUCK输出，这里是使能BUCK的输出
 *
 * @param 	[in]	buck_flag: BUCK序号，为2时控制所有
 *					[in]	EnableNotDisable: 使能或者关闭
 *
 * @return				None
 */
void Enable_LP87702_BUCK(uint8_t buck_flag,bool EnableNotDisable)
{
	uint8_t dat=0;
	uint8_t add=0;
	
	if(buck_flag>=2)
	{
		Enable_LP87702_BUCK(0,EnableNotDisable);
		Enable_LP87702_BUCK(1,EnableNotDisable);
	}
	else
	{	
		add = LP87702_BUCK0_CTRL_1+2*buck_flag;		
		dat=I2C_Read_y(&hi2c2,LP87702_Slave_Add,add,1,1,true);
		
		if(EnableNotDisable)
		{
			dat|=(1<<0);
		}
		else
		{
			dat&=~(1<<0);
		}
		
		I2C_Write_x(&hi2c4,LP87702_Slave_Add,add,1,&dat,1,true);
	}
}

/*!
 * @brief       	开启/关闭BOOST
 *
 * @param 	[in]	EnableNotDisable: 使能或者关闭
 *
 * @return				None
 */
void Enable_LP87702_BOOST(bool EnableNotDisable)
{
	uint8_t dat=0;
	
	dat=I2C_Read_y(&hi2c4,LP87702_Slave_Add,LP87702_BOOST_CTRL,1,1,true);	
	
	if(EnableNotDisable)
	{
		dat|=(1<<0);
	}
	else
	{	
		dat&=~(1<<0);
	}	
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_BOOST_CTRL,1,&dat,1,true);
}

/*!
 * @brief       	开启/关闭CLKIN引脚对看门狗的使能控制
 *
 * @param 	[in]	EnableNotDisable: 使能或者关闭
 *
 * @return				None
 */
void Enable_LP87702_WD_Pin_CON(bool EnableNotDisable)
{
	uint8_t dat=0;
	
	dat=0x87;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_WD_DIS_CTRL_CODE,1,&dat,1,true);
	dat=0x65;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_WD_DIS_CTRL_CODE,1,&dat,1,true);
	dat=0x1B;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_WD_DIS_CTRL_CODE,1,&dat,1,true);
	
	if(EnableNotDisable)
	{
		dat=0x01;
	}
	else
	{	
		dat=0x00;
	}
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_WD_DIS_CONTROL,1,&dat,1,true);
	
	dat=0xFF;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_WD_DIS_CTRL_CODE,1,&dat,1,true);
}

/*!
 * @brief       	初始化LP87702
 *
 * @param 				None
 *
 * @return				0/1: 错误/正确标志
 */
uint8_t Init_LP87702(void)
{
	uint8_t dat=0;
	
	Enable_VCC_5V;
	delay_ms(5);
	Enable_LP87702_EN;	
	delay_ms(5);
	
	if(!I2C_Judge(&hi2c4,LP87702_Slave_Add))
	{
		return 0;
	}
	
	if(!Reset_LP87702())
	{
		return 0;
	}
	
	dat=0x00;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_CONFIG,1,&dat,1,true);
	
	Enable_LP87702_WD_Pin_CON(true);
	
	dat=0x00;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_WD_CTRL_2,1,&dat,1,true);
	
	dat=0x08;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_BUCK0_CTRL_1,1,&dat,1,true);
	dat=0x1A;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_BUCK0_CTRL_2,1,&dat,1,true);
	dat=0x08;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_BUCK1_CTRL_1,1,&dat,1,true);
	dat=0x1A;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_BUCK1_CTRL_2,1,&dat,1,true);
	
	Ctrl_LP87702_BUCK_VOUT(0,1.8,true);
	Ctrl_LP87702_BUCK_VOUT(1,1.0,true);
	
	dat=0x58;
	I2C_Write_x(&hi2c4,LP87702_Slave_Add,LP87702_BOOST_CTRL,1,&dat,1,true);
	
	delay_ms(10);
	
	Enable_LP87702_BUCK(2,true);
	
	Enable_LP87702_BOOST(true);
	
	return 1;
}

/*!
 * @brief       	复位LP87524
 *
 * @param 				None
 *
 * @return				false/true: 错误/正确标志
 */
bool Reset_LP87524(void)
{
	uint8_t dat=0;
	dat=0x01;
	if(I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_RESET,1,&dat,1,true)!=true)
	{
		return false;
	}
	delay_ms(10);
	return true;
}

/*!
 * @brief       	控制LP87524的BUCK输出值，这里只控制VOUT，不控制FLOOR_VOUT
 *
 * @param 	[in]	buck_flag: BUCK序号，为4时控制所有
 *					[in]	voltage: 要输出的电压值
 *					[in]	WriteNotRead: 写入或读取
 *
 * @return				voltage_v: 写入或读取的电压值，控制所有时，写入的都为3.3V，读取的为四个电压值之和
 */
float Ctrl_LP87524_BUCK_VOUT(uint8_t buck_flag,float voltage_v,bool WriteNotRead)
{
	uint8_t dat=0;
	uint8_t add=0;	
	
	if(buck_flag>=4)
	{
		voltage_v=Ctrl_LP87524_BUCK_VOUT(0,3.3,WriteNotRead)+Ctrl_LP87524_BUCK_VOUT(1,3.3,WriteNotRead)+Ctrl_LP87524_BUCK_VOUT(2,3.3,WriteNotRead)+Ctrl_LP87524_BUCK_VOUT(3,3.3,WriteNotRead);
	}
	else
	{
		add = LP87524_BUCK0_VOUT+2*buck_flag;
		if(WriteNotRead)
		{
			
			if(voltage_v>=0.6f && voltage_v<=0.73f)
			{
				dat=0x0A+(voltage_v-0.6f)/0.01f;
			}
			else if(voltage_v>0.73f && voltage_v<=1.4f)
			{
				dat=0x17+(voltage_v-0.73f)/0.005f;
			}
			else if(voltage_v>1.4f && voltage_v<=3.36f)
			{
				dat=0x9D+(voltage_v-1.4f)/0.02f;
			}
			else
			{
				dat=0;
			}
			
			I2C_Write_x(&hi2c2,LP87524_Slave_Add,add,1,&dat,1,true);
		}
		else
		{
			dat=I2C_Read_y(&hi2c2,LP87524_Slave_Add,add,1,1,true);	
			
			if(dat>=0x0A && dat<=0x17)
			{
				voltage_v=(dat-0x0A)*0.01f+0.6f;
			}
			else if(dat>0x17 && dat<=0x9D)
			{
				voltage_v=(dat-0x17)*0.005f+0.73f;
			}
			else if(dat>=0x9D && dat<=0xFF)
			{
				voltage_v=(dat-0x9D)*0.02f+1.4f;
			}
			else
			{
				voltage_v=0;
			}
		}
	}	
	
	return voltage_v;
}

/*!
 * @brief       	开启LP87524的BUCK输出，这里是使能BUCK的输出，同时对应引脚置高电平
 *								初始化配置的是打开VOUT输出，如果要控制打开/关闭 VOUT/FLOOR_VOUT则需要另外配置
 *
 * @param 	[in]	buck_flag: BUCK序号，为4时控制所有
 *					[in]	EnableNotDisable: 使能或者关闭
 *
 * @return				None
 */
void Enable_LP87524_BUCK(uint8_t buck_flag,bool EnableNotDisable)
{
	uint8_t dat=0;
	uint8_t add=0;
	
	if(buck_flag>=4)
	{
		Enable_LP87524_BUCK(0,EnableNotDisable);
		Enable_LP87524_BUCK(1,EnableNotDisable);
		Enable_LP87524_BUCK(2,EnableNotDisable);
		Enable_LP87524_BUCK(3,EnableNotDisable);
	}
	else
	{	
		add = LP87524_BUCK0_CTRL1+2*buck_flag;		
		dat=I2C_Read_y(&hi2c2,LP87524_Slave_Add,add,1,1,true);
		
		if(EnableNotDisable)
		{
			dat|=(1<<7);
		}
		else
		{
			dat&=~(1<<7);
		}
		
		I2C_Write_x(&hi2c2,LP87524_Slave_Add,add,1,&dat,1,true);
		
		switch(buck_flag)
		{
			case 1:
			{			
				if(EnableNotDisable)
				{
					Enable_LP87524_EN1;
				}
				else
				{
					Disable_LP87524_EN1;
				}
				break;
			}
			case 2:
			{
				if(EnableNotDisable)
				{
					Enable_LP87524_EN2;
				}
				else
				{
					Disable_LP87524_EN2;
				}
				break;
			}
			case 3:
			{
				if(EnableNotDisable)
				{
					Enable_LP87524_EN3;
				}
				else
				{
					Disable_LP87524_EN3;
				}
				break;
			}
			default:break;
		}
	}
}

/*!
 * @brief       	初始化LP87524
 *
 * @param 				None
 *
 * @return				0/1: 错误/正确标志
 */
uint8_t Init_LP87524(void)
{
	uint8_t dat=0;
	
	Enable_VCC_5V;
	delay_ms(5);
	Disable_LP87524_EN1;
	Disable_LP87524_EN2;
	Disable_LP87524_EN3;
	delay_ms(5);
	
	if(!I2C_Judge(&hi2c2,LP87524_Slave_Add))
	{
		return 0;
	}
	
	if(!Reset_LP87524())
	{
		return 0;
	}
	
	dat=0x40;
	I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_CONFIG,1,&dat,1,true);
	
	dat=0x00;
	I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_PIN_FUNCTION,1,&dat,1,true);
	
	dat=0x34;
	I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_BUCK0_CTRL1,1,&dat,1,true);
	dat=0x44;
	I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_BUCK1_CTRL1,1,&dat,1,true);
	dat=0x54;
	I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_BUCK2_CTRL1,1,&dat,1,true);
	dat=0x64;
	I2C_Write_x(&hi2c2,LP87524_Slave_Add,LP87524_BUCK3_CTRL1,1,&dat,1,true);
	
	Ctrl_LP87524_BUCK_VOUT(0,3.3,true);
	Ctrl_LP87524_BUCK_VOUT(1,1.8,true);
	Ctrl_LP87524_BUCK_VOUT(2,1.2,true);
	Ctrl_LP87524_BUCK_VOUT(3,1.0,true);
	
	delay_ms(10);
	
	Enable_LP87524_BUCK(4,true);
	
	return 1;
}

附录：结构框架

雷达基本原理叙述

雷达工作原理是上电-发送chirps-帧结束-处理-上电循环
一个Frame，首先是信号发送，比如96个chirp就顺次发出去，然后接收回来，混频滤波，ADC采样，这些都是射频模块的东西。射频完成之后，FFT，CFAR，DOA这些就是信号处理的东西。然后输出给那个结构体，就是当前帧获得的点云了。
在这里插入图片描述
在射频发送阶段一个frame发送若干个chirp 也就是上图左上角
第一个绿色点为frame start 第二个绿色点为frame end
其中发送若干chirps（小三角形）
chirps的个数称为numLoops（代码中 rlFrameCfg_t结构体）
在mmwave studio上位机中则称为 no of chirp loops

frame end 到周期结束的时间为计算时间称为inter frame period
在这里插入图片描述
frame start到循环结束的时间称为framePeriodicity（代码中 rlFrameCfg_t结构体）
在mmwave studio上位机中则称为 Periodicity

如下图frame配置部分
在这里插入图片描述
在inter frame Periodicity时间内（比如这里整个周期是55ms）
就是用于计算和处理的时间一定比55ms要小
如果chirps很多的话那么计算时间就会减小

如果是处理点云数据则只需要每一帧计算一次点云即可
计算出当前帧的xyz坐标和速度以及保存时间戳

雷达天线排列位置

在工业雷达包：

C:\ti\mmwave_industrial_toolbox_4_12_0\antennas\ant_rad_patterns

路径下有各个EVM开发板的天线排列说明
同样的 EVM手册中也有
如IWR6843AOPEVM：
在这里插入图片描述

其天线的间距等等位于数据手册：

芯片框架

IWR6843AOP可以分成三个主要部分及多个外设
BSS：雷达前端部分
MSS：cortex-rf4内核主要用于控制
DSS： DSP C674内核主要用于信号处理
外设：UART GPIO DPM HWA等

在这里插入图片描述
其中大部分外设可以被MSS或DSS调用
另外雷达前端BSS部分在SDK里由MMWave API调用

代码框架上可以分成两个代码 MSS和DSS 两个代码同时运行通过某些外设进行同步协同运作

但也可以只跑一个内核在仅MSS模式下依旧可以调用某些用于信号处理的外设 demo代码就是如此

如下图为demo代码流程
在这里插入图片描述

Demo工程功能

IWR6843AOP的开箱工程是根据IWR6843AOPEVM开发板来的
该工程可以将IWR6843AOP的两个串口利用起来实现的功能主要是两个方面：
通过115200波特率的串口配置参数建立握手协议
通过115200*8的串口输出雷达数据
此工程需要匹配TI官方的上位机：mmWave_Demo_Visualizer_3.6.0来使用
该上位机可以在连接串口后自动化操作并且对雷达数据可视化
在这里插入图片描述

关于雷达参数配置则在SDK的mmw\profiles目录下
言简意赅可以直接更改该目录下的文件参数来达到配置雷达参数的目的

但这种方法不利于直接更改每次用上位机运行后的参数是固定的（上位机运行需要SDK环境）所以也可以在代码中写死本文探讨的就是这个方向

CCS工程导入

首先在工业雷达包目录下找到该工程设置

C:\ti\mmwave_industrial_toolbox_4_12_0\labs\Out_Of_Box_Demo\src\xwr6843AOP

使用CCS的import project功能导入工程后即可完成环境搭建
在这里插入图片描述
这里用到的SDK最新版为3.6版本

工程叙述

以下来自官方文档可以直接跳过

Software Tasks

The demo consists of the following (SYSBIOS) tasks:

MmwDemo_initTask. This task is created/launched by main and is a one-time active task whose main functionality is to initialize drivers (<driver>_init), MMWave module (MMWave_init), DPM module (DPM_init), open UART and data path related drivers (EDMA, HWA), and create/launch the following tasks (the CLI_task is launched indirectly by calling CLI_open).
CLI_task. This command line interface task provides a simplified 'shell' interface which allows the configuration of the BSS via the mmWave interface (MMWave_config). It parses input CLI configuration commands like chirp profile and GUI configuration. When sensor start CLI command is parsed, all actions related to starting sensor and starting the processing the data path are taken. When sensor stop CLI command is parsed, all actions related to stopping the sensor and stopping the processing of the data path are taken
MmwDemo_mmWaveCtrlTask. This task is used to provide an execution context for the mmWave control, it calls in an endless loop the MMWave_execute API.
MmwDemo_DPC_ObjectDetection_dpmTask. This task is used to provide an execution context for DPM (Data Path Manager) execution, it calls in an endless loop the DPM_execute API. In this context, all of the registered object detection DPC (Data Path Chain) APIs like configuration, control and execute will take place. In this task. When the DPC's execute API produces the detected objects and other results, they are transmitted out of the UART port for display using the visualizer.

Data Path

在这里插入图片描述
Top Level Data Path Processing Chain

Top Level Data Path Timing

The data path processing consists of taking ADC samples as input and producing detected objects (point-cloud and other information) to be shipped out of UART port to the PC. The algorithm processing is realized using the DPM registered Object Detection DPC. The details of the processing in DPC can be seen from the following doxygen documentation:

ti/datapath/dpc/objectdetection/objdethwa/docs/doxygen/html/index.html

Output information sent to host

Output packets with the detection information are sent out every frame through the UART. Each packet consists of the header MmwDemo_output_message_header_t and the number of TLV items containing various data information with types enumerated in MmwDemo_output_message_type_e. The numerical values of the types can be found in mmw_output.h. Each TLV item consists of type, length (MmwDemo_output_message_tl_t) and payload information. The structure of the output packet is illustrated in the following figure. Since the length of the packet depends on the number of detected objects it can vary from frame to frame. The end of the packet is padded so that the total packet length is always multiple of 32 Bytes.

在这里插入图片描述
Output packet structure sent to UART
The following subsections describe the structure of each TLV.

List of detected objects

Type: (MMWDEMO_OUTPUT_MSG_DETECTED_POINTS)

Length: (Number of detected objects) x (size of DPIF_PointCloudCartesian_t)

Value: Array of detected objects. The information of each detected object is as per the structure DPIF_PointCloudCartesian_t. When the number of detected objects is zero, this TLV item is not sent. The maximum number of objects that can be detected in a sub-frame/frame is DPC_OBJDET_MAX_NUM_OBJECTS.

The orientation of x,y and z axes relative to the sensor is as per the following figure. (Note: The antenna arrangement in the figure is shown for standard EVM (see gAntDef_default) as an example but the figure is applicable for any antenna arrangement.)

在这里插入图片描述
Coordinate Geometry
The whole detected objects TLV structure is illustrated in figure below.

Detected objects TLV

Range profile

Type: (MMWDEMO_OUTPUT_MSG_RANGE_PROFILE)

Length: (Range FFT size) x (size of uint16_t)

Value: Array of profile points at 0th Doppler (stationary objects). The points represent the sum of log2 magnitudes of received antennas expressed in Q9 format.

Noise floor profile
Type: (MMWDEMO_OUTPUT_MSG_NOISE_PROFILE)

Length: (Range FFT size) x (size of uint16_t)

Value: This is the same format as range profile but the profile is at the maximum Doppler bin (maximum speed objects). In general for stationary scene, there would be no objects or clutter at maximum speed so the range profile at such speed represents the receiver noise floor.

Azimuth static heatmap

Type: (MMWDEMO_OUTPUT_MSG_AZIMUT_STATIC_HEAT_MAP)

Length: (Range FFT size) x (Number of "azimuth" virtual antennas) (size of cmplx16ImRe_t_)

Value: Array DPU_AoAProcHWA_HW_Resources::azimuthStaticHeatMap. The antenna data are complex symbols, with imaginary first and real second in the following order:

Imag(ant 0, range 0), Real(ant 0, range 0),...,Imag(ant N-1, range 0),Real(ant N-1, range 0)
         ...
         Imag(ant 0, range R-1), Real(ant 0, range R-1),...,Imag(ant N-1, range R-1),Real(ant N-1, range R-1)

Note that the number of virtual antennas is equal to the number of “azimuth” virtual antennas. The antenna symbols are arranged in the order as they occur at the input to azimuth FFT. Based on this data the static azimuth heat map could be constructed by the GUI running on the host.

Azimuth/Elevation static heatmap

Type: (MMWDEMO_OUTPUT_MSG_AZIMUT_ELEVATION_STATIC_HEAT_MAP)

Length: (Range FFT size) x (Number of all virtual antennas) (size of cmplx16ImRe_t_)

Value: Array DPU_AoAProcHWA_HW_Resources::azimuthStaticHeatMap. The antenna data are complex symbols, with imaginary first and real second in the following order:

 Imag(ant 0, range 0), Real(ant 0, range 0),...,Imag(ant N-1, range 0),Real(ant N-1, range 0)
         ...
         Imag(ant 0, range R-1), Real(ant 0, range R-1),...,Imag(ant N-1, range R-1),Real(ant N-1, range R-1)

Note that the number of virtual antennas is equal to the total number of active virtual antennas. The antenna symbols are arranged in the order as they occur in the radar cube matrix. This TLV is sent by AOP version of MMW demo, that uses AOA2D DPU. Based on this data the static azimuth or elevation heat map could be constructed by the GUI running on the host.

Range/Doppler heatmap

Type: (MMWDEMO_OUTPUT_MSG_RANGE_DOPPLER_HEAT_MAP)

Length: (Range FFT size) x (Doppler FFT size) (size of uint16_t)

Value: Detection matrix DPIF_DetMatrix::data. The order is :

 X(range bin 0, Doppler bin 0),...,X(range bin 0, Doppler bin D-1),
        ...
        X(range bin R-1, Doppler bin 0),...,X(range bin R-1, Doppler bin D-1)

Stats information

Type: (MMWDEMO_OUTPUT_MSG_STATS )

Length: (size of MmwDemo_output_message_stats_t)

Value: Timing information as per MmwDemo_output_message_stats_t. See timing diagram below related to the stats.

在这里插入图片描述
Processing timing

Note:

The MmwDemo_output_message_stats_t::interChirpProcessingMargin is not computed (it is always set to 0). This is because there is no CPU involvement in the 1D processing (only HWA and EDMA are involved), and it is not possible to know how much margin is there in chirp processing without CPU being notified at every chirp when processing begins (chirp event) and when the HWA-EDMA computation ends. The CPU is intentionally kept free during 1D processing because a real application may use this time for doing some post-processing algorithm execution.
While the MmwDemo_output_message_stats_t::interFrameProcessingTime reported will be of the current sub-frame/frame, the MmwDemo_output_message_stats_t::interFrameProcessingMargin and MmwDemo_output_message_stats_t::transmitOutputTime will be of the previous sub-frame (of the same MmwDemo_output_message_header_t::subFrameNumber as that of the current sub-frame) or of the previous frame.
The MmwDemo_output_message_stats_t::interFrameProcessingMargin excludes the UART transmission time (available as MmwDemo_output_message_stats_t::transmitOutputTime). This is done intentionally to inform the user of a genuine inter-frame processing margin without being influenced by a slow transport like UART, this transport time can be significantly longer for example when streaming out debug information like heat maps. Also, in a real product deployment, higher speed interfaces (e.g LVDS) are likely to be used instead of UART. User can calculate the margin that includes transport overhead (say to determine the max frame rate that a particular demo configuration will allow) using the stats because they also contain the UART transmission time.

The CLI command “guMonitor” specifies which TLV element will be sent out within the output packet. The arguments of the CLI command are stored in the structure MmwDemo_GuiMonSel_t.

Side information of detected objects

Type: (MMWDEMO_OUTPUT_MSG_DETECTED_POINTS_SIDE_INFO)

Length: (Number of detected objects) x (size of DPIF_PointCloudSideInfo_t)

Value: Array of detected objects side information. The side information of each detected object is as per the structure DPIF_PointCloudSideInfo_t). When the number of detected objects is zero, this TLV item is not sent.

Temperature Stats

Type: (MMWDEMO_OUTPUT_MSG_TEMPERATURE_STATS)

Length: (size of MmwDemo_temperatureStats_t)

Value: Structure of detailed temperature report as obtained from Radar front end. MmwDemo_temperatureStats_t::tempReportValid is set to return value of rlRfGetTemperatureReport. If MmwDemo_temperatureStats_t::tempReportValid is 0, values in MmwDemo_temperatureStats_t::temperatureReport are valid else they should be ignored. This TLV is sent along with Stats TLV described in Stats information

Range Bias and Rx Channel Gain/Phase Measurement and Compensation

Because of imperfections in antenna layouts on the board, RF delays in SOC, etc, there is need to calibrate the sensor to compensate for bias in the range estimation and receive channel gain and phase imperfections. The following figure illustrates the calibration procedure.

在这里插入图片描述
Calibration procedure ladder diagram

The calibration procedure includes the following steps:

Set a strong target like corner reflector at the distance of X meter (X less than 50 cm is not recommended) at boresight.
Set the following command in the configuration profile in .../profiles/profile_calibration.cfg, to reflect the position X as follows: where D (in meters) is the distance of window around X where the peak will be searched. The purpose of the search window is to allow the test environment from not being overly constrained say because it may not be possible to clear it of all reflectors that may be stronger than the one used for calibration. The window size is recommended to be at least the distance equivalent of a few range bins. One range bin for the calibration profile (profile_calibration.cfg) is about 5 cm. The first argument "1" is to enable the measurement. The stated configuration profile (.cfg) must be used otherwise the calibration may not work as expected (this profile ensures all transmit and receive antennas are engaged among other things needed for calibration).
   measureRangeBiasAndRxChanPhase 1 X D
Start the sensor with the configuration file.
In the configuration file, the measurement is enabled because of which the DPC will be configured to perform the measurement and generate the measurement result (DPU_AoAProc_compRxChannelBiasCfg_t) in its result structure (DPC_ObjectDetection_ExecuteResult_t::compRxChanBiasMeasurement), the measurement results are written out on the CLI port (MmwDemo_measurementResultOutput) in the format below: For details of how DPC performs the measurement, see the DPC documentation.
   compRangeBiasAndRxChanPhase <rangeBias> <Re(0,0)> <Im(0,0)> <Re(0,1)> <Im(0,1)> ... <Re(0,R-1)> <Im(0,R-1)> <Re(1,0)> <Im(1,0)> ... <Re(T-1,R-1)> <Im(T-1,R-1)>
The command printed out on the CLI now can be copied and pasted in any configuration file for correction purposes. This configuration will be passed to the DPC for the purpose of applying compensation during angle computation, the details of this can be seen in the DPC documentation. If compensation is not desired, the following command should be given (depending on the EVM and antenna arrangement) Above sets the range bias to 0 and the phase coefficients to unity so that there is no correction. Note the two commands must always be given in any configuration file, typically the measure commmand will be disabled when the correction command is the desired one.
   For ISK EVM:
   compRangeBiasAndRxChanPhase 0.0   1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 
   For AOP EVM
   compRangeBiasAndRxChanPhase 0.0   1 0 -1 0 1 0 -1 0 1 0 -1 0 1 0 -1 0 1 0 -1 0 1 0 -1 0

Streaming data over LVDS

The LVDS streaming feature enables the streaming of HW data (a combination of ADC/CP/CQ data) and/or user specific SW data through LVDS interface. The streaming is done mostly by the CBUFF and EDMA peripherals with minimal CPU intervention. The streaming is configured through the MmwDemo_LvdsStreamCfg_t CLI command which allows control of HSI header, enable/disable of HW and SW data and data format choice for the HW data. The choices for data formats for HW data are:

MMW_DEMO_LVDS_STREAM_CFG_DATAFMT_DISABLED
MMW_DEMO_LVDS_STREAM_CFG_DATAFMT_ADC
MMW_DEMO_LVDS_STREAM_CFG_DATAFMT_CP_ADC_CQ
In order to see the high-level data format details corresponding to the above data format configurations, refer to the corresponding slides in ti\drivers\cbuff\docs\CBUFF_Transfers.pptx

When HW data LVDS streaming is enabled, the ADC/CP/CQ data is streamed per chirp on every chirp event. When SW data streaming is enabled, it is streamed during inter-frame period after the list of detected objects for that frame is computed. The SW data streamed every frame/sub-frame is composed of the following in time:

HSI header (HSIHeader_t): refer to HSI module for details.
User data header: MmwDemo_LVDSUserDataHeader
User data payloads:
Point-cloud information as a list : DPIF_PointCloudCartesian_t x number of detected objects
Point-cloud side information as a list : DPIF_PointCloudSideInfo_t x number of detected objects

The format of the SW data streamed is shown in the following figure:
在这里插入图片描述
LVDS SW Data format

Note:

Only single-chirp formats are allowed, multi-chirp is not supported.
When number of objects detected in frame/sub-frame is 0, there is no transmission beyond the user data header.
For HW data, the inter-chirp duration should be sufficient to stream out the desired amount of data. For example, if the HW data-format is ADC and HSI header is enabled, then the total amount of data generated per chirp is:
(numAdcSamples * numRxChannels * 4 (size of complex sample) + 52 [sizeof(HSIDataCardHeader_t) + sizeof(HSISDKHeader_t)] ) rounded up to multiples of 256 [=sizeof(HSIHeader_t)] bytes.
The chirp time Tc in us = idle time + ramp end time in the profile configuration. For n-lane LVDS with each lane at a maximum of B Mbps,
maximum number of bytes that can be send per chirp = Tc * n * B / 8 which should be greater than the total amount of data generated per chirp i.e
Tc * n * B / 8 >= round-up(numAdcSamples * numRxChannels * 4 + 52, 256).
E.g if n = 2, B = 600 Mbps, idle time = 7 us, ramp end time = 44 us, numAdcSamples = 512, numRxChannels = 4, then 7650 >= 8448 is violated so this configuration will not work. If the idle-time is doubled in the above example, then we have 8700 > 8448, so this configuration will work.
For SW data, the number of bytes to transmit each sub-frame/frame is:
52 [sizeof(HSIDataCardHeader_t) + sizeof(HSISDKHeader_t)] + sizeof(MmwDemo_LVDSUserDataHeader_t) [=8] +
number of detected objects (Nd) * { sizeof(DPIF_PointCloudCartesian_t) [=16] + sizeof(DPIF_PointCloudSideInfo_t) [=4] } rounded up to multiples of 256 [=sizeof(HSIHeader_t)] bytes.
or X = round-up(60 + Nd * 20, 256). So the time to transmit this data will be
X * 8 / (n*B) us. The maximum number of objects (Ndmax) that can be detected is defined in the DPC (DPC_OBJDET_MAX_NUM_OBJECTS). So if Ndmax = 500, then time to transmit SW data is 68 us. Because we parallelize this transmission with the much slower UART transmission, and because UART transmission is also sending at least the same amount of information as the LVDS, the LVDS transmission time will not add any burdens on the processing budget beyond the overhead of reconfiguring and activating the CBUFF session (this overhead is likely bigger than the time to transmit).
The total amount of data to be transmitted in a HW or SW packet must be greater than the minimum required by CBUFF, which is 64 bytes or 32 CBUFF Units (this is the definition CBUFF_MIN_TRANSFER_SIZE_CBUFF_UNITS in the CBUFF driver implementation). If this threshold condition is violated, the CBUFF driver will return an error during configuration and the demo will generate a fatal exception as a result. When HSI header is enabled, the total transfer size is ensured to be at least 256 bytes, which satisfies the minimum. If HSI header is disabled, for the HW session, this means that numAdcSamples * numRxChannels * 4 >= 64. Although mmwavelink allows minimum number of ADC samples to be 2, the demo is supported for numAdcSamples >= 64. So HSI header is not required to be enabled for HW only case. But if SW session is enabled, without the HSI header, the bytes in each packet will be 8 + Nd * 20. So for frames/sub-frames where Nd < 3, the demo will generate exception. Therefore HSI header must be enabled if SW is enabled, this is checked in the CLI command validation.

Implementation Notes

The LVDS implementation is mostly present in mmw_lvds_stream.h and mmw_lvds_stream.c with calls in mss_main.c. Additionally HSI clock initialization is done at first time sensor start using MmwDemo_mssSetHsiClk.
EDMA channel resources for CBUFF/LVDS are in the global resource file (mmw_res.h, see Hardware Resource Allocation) along with other EDMA resource allocation. The user data header and two user payloads are configured as three user buffers in the CBUFF driver. Hence SW allocation for EDMA provides for three sets of EDMA resources as seen in the SW part (swSessionEDMAChannelTable[.]) of MmwDemo_LVDSStream_EDMAInit. The maximum number of HW EDMA resources are needed for the data-format MMW_DEMO_LVDS_STREAM_CFG_DATAFMT_CP_ADC_CQ, which as seen in the corresponding slide in ti\drivers\cbuff\docs\CBUFF_Transfers.pptx is 12 channels (+ shadows) including the 1st special CBUFF EDMA event channel which CBUFF IP generates to the EDMA, hence the HW part (hwwSessionEDMAChannelTable[.]) of MmwDemo_LVDSStream_EDMAInit has 11 table entries.
Although the CBUFF driver is configured for two sessions (hw and sw), at any time only one can be active. So depending on the LVDS CLI configuration and whether advanced frame or not, there is logic to activate/deactivate HW and SW sessions as necessary.
The CBUFF session (HW/SW) configure-create and delete depends on whether or not re-configuration is required after the first time configuration.
For HW session, re-configuration is done during sub-frame switching to re-configure for the next sub-frame but when there is no advanced frame (number of sub-frames = 1), the HW configuration does not need to change so HW session does not need to be re-created.
For SW session, even though the user buffer start addresses and sizes of headers remains same, the number of detected objects which determines the sizes of some user buffers changes from one sub-frame/frame to another sub-frame/frame. Therefore SW session needs to be recreated every sub-frame/frame.
User may modify the application software to transmit different information than point-cloud in the SW data e.g radar cube data (output of range DPU). However the CBUFF also has a maximum link list entry size limit of 0x3FFF CBUFF units or 32766 bytes. This means it is the limit for each user buffer entry [there are maximum of 3 entries -1st used for user data header, 2nd for point-cloud and 3rd for point-cloud side information]. During session creation, if this limit is exceeded, the CBUFF will return an error (and demo will in turn generate an exception). A single physical buffer of say size 50000 bytes may be split across two user buffers by providing one user buffer with (address, size) = (start address, 25000) and 2nd user buffer with (address, size) = (start address + 25000, 25000), beyond this two (or three if user data header is also replaced) limit, the user will need to create and activate (and wait for completion) the SW session multiple times to accomplish the transmission.

The following figure shows a timing diagram for the LVDS streaming (the figure is not to scale as actual durations will vary based on configuration).
在这里插入图片描述

How to bypass CLI

Re-implement the file mmw_cli.c as follows:

MmwDemo_CLIInit should just create a task with input taskPriority. Lets say the task is called "MmwDemo_sensorConfig_task".
All other functions are not needed
Implement the MmwDemo_sensorConfig_task as follows:
Fill gMmwMCB.cfg.openCfg
Fill gMmwMCB.cfg.ctrlCfg
Add profiles and chirps using MMWave_addProfile and MMWave_addChirp functions
Call MmwDemo_CfgUpdate for every offset in Offsets for storing CLI configuration (MMWDEMO_xxx_OFFSET in mmw.h)
Fill gMmwMCB.dataPathObj.objDetCommonCfg.preStartCommonCfg
Call MmwDemo_openSensor
Call MmwDemo_startSensor (One can use helper function MmwDemo_isAllCfgInPendingState to know if all dynamic config was provided)

Hardware Resource Allocation

The Object Detection DPC needs to configure the DPUs hardware resources (HWA, EDMA). Even though the hardware resources currently are only required to be allocated for this one and only DPC in the system, the resource partitioning is shown to be in the ownership of the demo. This is to illustrate the general case of resource allocation across more than one DPCs and/or demo's own processing that is post-DPC processing. This partitioning can be seen in the mmw_res.h file. This file is passed as a compiler command line define

"--define=APP_RESOURCE_FILE="<ti/demo/xwr64xx/mmw/mmw_res.h>"

in mmw.mak when building the DPC sources as part of building the demo application and is referred in object detection DPC sources where needed as

#include APP_RESOURCE_FILE