20230213在AIO-3568J开发板在原厂Android12下跑通ap6275s
2023/2/13 8:59
一、从AIO-3568的Android11的kernel中抠出来AP6275S的驱动：
1、
Z:\android12-rk3588-new\kernel-4.19\arch\arm64\configs\rockchip_defconfig
# CONFIG_WLAN_VENDOR_QUANTENNA is not set
CONFIG_WL_ROCKCHIP=y
CONFIG_WIFI_BUILD_MODULE=y
CONFIG_AP6XXX=m
CONFIG_RTL8723CS=m
CONFIG_RTL8821CS=m
CONFIG_RTL8822BS=m
CONFIG_LTE=y
修改为：
CONFIG_WL_ROCKCHIP=y
CONFIG_WIFI_BUILD_MODULE=y
#CONFIG_AP6XXX=m
# CONFIG_AP6XXX is not set
CONFIG_AP6275S=m
CONFIG_RTL8723CS=m
CONFIG_RTL8821CS=m
CONFIG_RTL8822BS=m
CONFIG_LTE=y
2、
Z:\android12-rk3588-new\kernel-4.19\drivers\net\wireless\rockchip_wlan\rkwifi\Kconfig
config AP6XXX_WIFI6
tristate "support wifi6(80211ax)"
#depends on MMC && WLAN_80211
select CFG80211
select MAC80211
help
This driver supports wifi6 for ap6xxx chipset.
This driver uses the kernel's wireless extensions subsystem.
If you choose to build a module, it'll be called dhd. Say M if
unsure.
config AP6275S
tristate "support wifi6 ap6275s(80211ax)"
#depends on MMC && WLAN_80211
select CFG80211
select MAC80211
---help---
This driver supports wifi6 for ap6275s chipset.
This driver uses the kernel's wireless extensions subsystem.
If you choose to build a module, it'll be called dhd. Say M if
unsure.
config AP6XXX_INDEP_POWER
tristate "support WiFi keepalive during host shutdown"
select CFG80211
select MAC80211
endchoice
3、
Z:\android12-rk3588-new\kernel-4.19\drivers\net\wireless\rockchip_wlan\rkwifi\Makefile
# SPDX-License-Identifier: GPL-2.0
#rkwifi packed Makefile
# (gwl)
obj-$(CONFIG_AP6XXX) += bcmdhd/
obj-$(CONFIG_AP6XXX_WIFI6) += bcmdhd_wifi6/
obj-$(CONFIG_AP6275S) += ap6275s/
obj-$(CONFIG_AP6XXX_INDEP_POWER) += bcmdhd_indep_power/
.PHONY: clean
clean:
find . -name '*.o*' -exec rm -f {} \;
4、【全部拷贝过来！】
Z:\android12-rk3588-new\kernel-4.19\drivers\net\wireless\rockchip_wlan\rkwifi\ap6275s\Makefile
二、
Z:\android12-rk3588-new\kernel-4.19\arch\arm64\boot\dts\rockchip\rk3568-evb.dtsi
1、
wireless_wlan: wireless-wlan {
compatible = "wlan-platdata";
rockchip,grf = <&grf>;
wifi_chip_type = "ap6398s";
status = "okay";
};
修改为：
wireless_wlan: wireless-wlan {
compatible = "wlan-platdata";
rockchip,grf = <&grf>;
wifi_chip_type = "ap6398s";
pinctrl-names = "default";
pinctrl-0 = <&wifi_host_wake_irq>;
WIFI,host_wake_irq = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
status = "okay";
};
2、
/*
* There are 10 independent IO domains in RK3566/RK3568, including PMUIO[0:2] and VCCIO[1:7].
* 1/ PMUIO0 and PMUIO1 are fixed-level power domains which cannot be configured;
* 2/ PMUIO2 and VCCIO1,VCCIO[3:7] domains require that their hardware power supply voltages
* must be consistent with the software configuration correspondingly
* a/ When the hardware IO level is connected to 1.8V, the software voltage configuration
* should also be configured to 1.8V accordingly;
* b/ When the hardware IO level is connected to 3.3V, the software voltage configuration
* should also be configured to 3.3V accordingly;
* 3/ VCCIO2 voltage control selection (0xFDC20140)
* BIT[0]: 0x0: from GPIO_0A7 (default)
* BIT[0]: 0x1: from GRF
* Default is determined by Pin FLASH_VOL_SEL/GPIO0_A7:
* L:VCCIO2 must supply 3.3V
* H:VCCIO2 must supply 1.8V
*/
&pmu_io_domains {
status = "okay";
pmuio2-supply = <&vcc3v3_pmu>;
vccio1-supply = <&vccio_acodec>;
vccio3-supply = <&vccio_sd>;
vccio4-supply = <&vcc_3v3>;
vccio5-supply = <&vcc_3v3>;
vccio6-supply = <&vcc_3v3>;
vccio7-supply = <&vcc_3v3>;
};
修改为：、
&pmu_io_domains {
status = "okay";
pmuio1-supply = <&vcc3v3_pmu>;
pmuio2-supply = <&vcc3v3_pmu>;
vccio1-supply = <&vccio_acodec>;
vccio3-supply = <&vccio_sd>;
vccio4-supply = <&vcc_1v8>;
vccio5-supply = <&vcc_3v3>;
vccio6-supply = <&vcc_1v8>;
vccio7-supply = <&vcc_3v3>;
};
三、
Z:\android12-rk3588-new\kernel-4.19\arch\arm64\boot\dts\rockchip\rk3568-evb2-lp4x-v10.dtsi
1、
ext_cam_clk: external-camera-clock {
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "CLK_CAMERA_24MHZ";
#clock-cells = <0>;
};
};
// firefly U mast add here for AP6275S
&sdmmc2 {
max-frequency = <150000000>;
supports-sdio;
bus-width = <4>;
disable-wp;
cap-sd-highspeed;
cap-sdio-irq;
keep-power-in-suspend;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
sd-uhs-sdr104;
mmc-pwrseq = <&sdio_pwrseq>;
non-removable;
status = "disabled";
};
&uart8 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn>;
};
&spi1 {
status = "disabled";
max-freq = <48000000>;
dev-port = <0>;
pinctrl-0 = <&spi1m1_pins>;
pinctrl-1 = <&spi1m1_pins_hs>;
spi_wk2xxx: spi_wk2xxx@00{
status = "disabled";
compatible = "firefly,spi-wk2xxx";
reg = <0x00>;
spi-max-frequency = <10000000>;
//power-gpio = <&pca9555 PCA_IO1_7 GPIO_ACTIVE_HIGH>;
//reset-gpio = <&pca9555 PCA_IO1_1 GPIO_ACTIVE_HIGH>;
irq-gpio = <&gpio0 RK_PA6 IRQ_TYPE_EDGE_FALLING>;
cs-gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
/* rk3399 driver support SPI_CPOL | SPI_CPHA | SPI_CS_HIGH */
//spi-cpha; /* SPI mode: CPHA=1 */
//spi-cpol; /* SPI mode: CPOL=1 */
//spi-cs-high;
};
};
// firefly
&combphy0_us {
status = "okay";
};
&combphy1_usq {
status = "okay";
};
&combphy2_psq {
status = "okay";
};
2、
&combphy0_us {
status = "okay";
};
&combphy1_usq {
status = "okay";
};
&combphy2_psq {
status = "okay";
};
// for AIO-3568J, you must add this Block for USB3
// firefly
&csi2_dphy0 {
status = "okay";
};
&csi2_dphy1 {
status = "disabled";
};
&csi2_dphy2 {
status = "disabled";
};
/*
// firefly
* video_phy0 needs to be enabled
* when dsi0 is enabled
*/
&dsi0 {
status = "okay";
};
&dsi0_in_vp0 {
status = "disabled";
};
如果没有这里，在你配置AP6275S的时钟为内置时钟之后，USB3就会打不开了！
[ 807.048984] read descriptors
[ 807.049025] read strings
[ 808.088976] read descriptors
[ 808.089018] read strings
[ 808.089867] init: processing action (sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1) from (/system/etc/init/hw/init.usb.configfs.rc:20)
[ 808.091168] init: Command 'symlink /config/usb_gadget/g1/functions/ffs.adb /config/usb_gadget/g1/configs/b.1/f1' action=sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1 (/system/etc/init/hw/init.usb.configfs.rc:22) took 0ms and failed: symlink() failed: File exists
[ 808.091339] init: Command 'write /config/usb_gadget/g1/UDC ${sys.usb.controller}' action=sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1 (/system/etc/init/hw/init.usb.configfs.rc:23) took 0ms and failed: property 'sys.usb.controller' doesn't exist while expanding '${sys.usb.controller}'
[ 809.139059] read descriptors
[ 809.139102] read strings
[ 809.139957] init: processing action (sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1) from (/system/etc/init/hw/init.usb.configfs.rc:20)
[ 809.141255] init: Command 'symlink /config/usb_gadget/g1/functions/ffs.adb /config/usb_gadget/g1/configs/b.1/f1' action=sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1 (/system/etc/init/hw/init.usb.configfs.rc:22) took 0ms and failed: symlink() failed: File exists
[ 809.141432] init: Command 'write /config/usb_gadget/g1/UDC ${sys.usb.controller}' action=sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1 (/system/etc/init/hw/init.usb.configfs.rc:23) took 0ms and failed: property 'sys.usb.controller' doesn't exist while expanding '${sys.usb.controller}'
[ 810.188992] read descriptors
[ 810.189030] read strings
[ 810.189891] init: processing action (sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1) from (/system/etc/init/hw/init.usb.configfs.rc:20)
[ 810.191162] init: Command 'symlink /config/usb_gadget/g1/functions/ffs.adb /config/usb_gadget/g1/configs/b.1/f1' action=sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1 (/system/etc/init/hw/init.usb.configfs.rc:22) took 0ms and failed: symlink() failed: File exists
[ 810.191335] init: Command 'write /config/usb_gadget/g1/UDC ${sys.usb.controller}' action=sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1 (/system/etc/init/hw/init.usb.configfs.rc:23) took 0ms and failed: property 'sys.usb.controller' doesn't exist while expanding '${sys.usb.controller}'
[ 811.232331] read descriptors
[ 811.232374] read strings
[ 811.233188] init: processing action (sys.usb.config=adb && sys.usb.configfs=1 && sys.usb.ffs.ready=1) from (/system/etc/init/hw/init.usb.configfs.rc:20)
[ 812.282315] read descriptors
3、
&dsi1_panel {
power-supply = <&vcc3v3_lcd1_n>;
};
// ToyBrick U must close this block for AP6275S
///*
//&gmac0 {
// phy-supply = <&qsgmii_3v3>;
// phy-mode = "qsgmii";
// rockchip,xpcs = <&xpcs>;
//
// assigned-clocks = <&cru SCLK_GMAC0_RX_TX>;
// assigned-clock-parents = <&gmac0_xpcsclk>;
//
// power-domains = <&power RK3568_PD_PIPE>;
// phys = <&combphy1_usq PHY_TYPE_QSGMII>;
// phy-handle = <&qsgmii_phy0>;
//
// status = "okay";
//};
//
//&gmac1 {
// phy-supply = <&qsgmii_3v3>;
// phy-mode = "qsgmii";
//
// snps,reset-gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
// snps,reset-active-low;
// /* Reset time is 20ms, 100ms for rtl8211f */
// snps,reset-delays-us = <0 20000 100000>;
//
// assigned-clocks = <&cru SCLK_GMAC1_RX_TX>;
// assigned-clock-parents = <&gmac1_xpcsclk>;
//
// pinctrl-names = "default";
// pinctrl-0 = <&gmac1m1_miim>;
//
// power-domains = <&power RK3568_PD_PIPE>;
// phy-handle = <&qsgmii_phy1>;
//
// status = "okay";
//};
//*/
/*
* power-supply should switche to vcc3v3_lcd1_n
* when mipi panel is connected to dsi1.
*/
>1x {
power-supply = <&vcc3v3_lcd0_n>;
};
4、
&pcie2x1 {
reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
vpcie3v3-supply = <&vcc3v3_pcie>;
status = "okay";
};
&pcie3x2 {
reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
vpcie3v3-supply = <&vcc3v3_pcie>;
status = "okay";
};
// fireffly
//&hym8563 {
// status = "okay";
//};
//
//&mc3230 {
// status = "okay";
//};
//&uart3 {
// status = "okay";
//};
&uart4 {
status = "okay";
};
&spi1 {
status = "okay";
};
//&spi_wk2xxx {
// status = "okay";
//};
// firefly
&pcie30phy {
status = "okay";
};
// fireffly
&pinctrl {
headphone {
hp_det: hp-det {
rockchip,pins = <4 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
5、
sii902x {
sii902x_hdmi_int: sii902x-hdmi-int {
rockchip,pins = <3 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
// ToyBrick U must close this block for AP6275S (BT)
/*
sdio-pwrseq {
wifi_enable_h: wifi-enable-h {
rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
};
wifi_32k: wifi-32k {
rockchip,pins = <2 RK_PC6 1 &pcfg_pull_none>;
};
};
*/
wireless-wlan {
wifi_host_wake_irq: wifi-host-wake-irq {
rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
//wireless-bluetooth {
// uart1_gpios: uart1-gpios {
// rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
// };
//};
usb {
vcc_hub_power_en: vcc-hub-power-en {
rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
};
vcc_hub_reset_en: vcc-hub-reset-en {
rockchip,pins = <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};
6、
// ToyBrick U must close this block for AP6275S
//&pmu_io_domains {
// vccio6-supply = <&vcc_3v3>;
//};
//
//&pwm3 {
// status = "okay";
//
// compatible = "rockchip,remotectl-pwm";
// remote_pwm_id = <3>;
// handle_cpu_id = <1>;
// remote_support_psci = <0>;
// pinctrl-names = "default";
// pinctrl-0 = <&pwm3_pins>;
//
// ir_key1 {
// rockchip,usercode = <0x4040>;
// rockchip,key_table =
// <0xf2 KEY_REPLY>,
// <0xba KEY_BACK>,
// <0xf4 KEY_UP>,
// <0xf1 KEY_DOWN>,
// <0xef KEY_LEFT>,
// <0xee KEY_RIGHT>,
// <0xbd KEY_HOME>,
// <0xea KEY_VOLUMEUP>,
// <0xe3 KEY_VOLUMEDOWN>,
// <0xe2 KEY_SEARCH>,
// <0xb2 KEY_POWER>,
// <0xbc KEY_MUTE>,
// <0xec KEY_MENU>,
// <0xbf 0x190>,
// <0xe0 0x191>,
// <0xe1 0x192>,
// <0xe9 183>,
// <0xe6 248>,
// <0xe8 185>,
// <0xe7 186>,
// <0xf0 388>,
// <0xbe 0x175>;
// };
//
// ir_key2 {
// rockchip,usercode = <0xff00>;
// rockchip,key_table =
// <0xf9 KEY_HOME>,
// <0xbf KEY_BACK>,
// <0xfb KEY_MENU>,
// <0xaa KEY_REPLY>,
// <0xb9 KEY_UP>,
// <0xe9 KEY_DOWN>,
// <0xb8 KEY_LEFT>,
// <0xea KEY_RIGHT>,
// <0xeb KEY_VOLUMEDOWN>,
// <0xef KEY_VOLUMEUP>,
// <0xf7 KEY_MUTE>,
// <0xe7 KEY_POWER>,
// <0xfc KEY_POWER>,
// <0xa9 KEY_VOLUMEDOWN>,
// <0xa8 KEY_VOLUMEDOWN>,
// <0xe0 KEY_VOLUMEDOWN>,
// <0xa5 KEY_VOLUMEDOWN>,
// <0xab 183>,
// <0xb7 388>,
// <0xe8 388>,
// <0xf8 184>,
// <0xaf 185>,
// <0xed KEY_VOLUMEDOWN>,
// <0xee 186>,
// <0xb3 KEY_VOLUMEDOWN>,
// <0xf1 KEY_VOLUMEDOWN>,
// <0xf2 KEY_VOLUMEDOWN>,
// <0xf3 KEY_SEARCH>,
// <0xb4 KEY_VOLUMEDOWN>,
// <0xbe KEY_SEARCH>;
// };
//
// ir_key3 {
// rockchip,usercode = <0x1dcc>;
// rockchip,key_table =
// <0xee KEY_REPLY>,
// <0xf0 KEY_BACK>,
// <0xf8 KEY_UP>,
// <0xbb KEY_DOWN>,
// <0xef KEY_LEFT>,
// <0xed KEY_RIGHT>,
// <0xfc KEY_HOME>,
// <0xf1 KEY_VOLUMEUP>,
// <0xfd KEY_VOLUMEDOWN>,
// <0xb7 KEY_SEARCH>,
// <0xff KEY_POWER>,
// <0xf3 KEY_MUTE>,
// <0xbf KEY_MENU>,
// <0xf9 0x191>,
// <0xf5 0x192>,
// <0xb3 388>,
// <0xbe KEY_1>,
// <0xba KEY_2>,
// <0xb2 KEY_3>,
// <0xbd KEY_4>,
// <0xf9 KEY_5>,
// <0xb1 KEY_6>,
// <0xfc KEY_7>,
// <0xf8 KEY_8>,
// <0xb0 KEY_9>,
// <0xb6 KEY_0>,
// <0xb5 KEY_BACKSPACE>;
// };
//};
//
//&pwm7 {
// status = "disabled";
//};
//
//&route_dsi0 {
// status = "okay";
// connect = <&vp1_out_dsi0>;
//};
// ToyBrick
7、
&sdio_pwrseq {
clocks = <&pmucru CLK_RTC_32K>;
pinctrl-0 = <&wifi_enable_h &wifi_32k>;
/*
* On the module itself this is one of these (depending
* on the actual card populated):
* - SDIO_RESET_L_WL_REG_ON
* - PDN (power down when low)
*/
reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
};
&sdmmc1 {
max-frequency = <150000000>;
supports-sdio;
bus-width = <4>;
disable-wp;
cap-sd-highspeed;
cap-sdio-irq;
keep-power-in-suspend;
mmc-pwrseq = <&sdio_pwrseq>;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
sd-uhs-sdr104;
status = "okay";
};
&sdmmc2 {
status = "disabled";
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
};
修改为：
&sdio_pwrseq {
status = "okay";
reset-gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
post-power-on-delay-ms = <100>;
};
// ToyBrick U must close this block for AP6275S
//&sdmmc1 {
// max-frequency = <150000000>;
// supports-sdio;
// bus-width = <4>;
// disable-wp;
// cap-sd-highspeed;
// cap-sdio-irq;
// keep-power-in-suspend;
// mmc-pwrseq = <&sdio_pwrseq>;
// non-removable;
// pinctrl-names = "default";
// pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
// sd-uhs-sdr104;
// status = "okay";
//};
&sdmmc2 {
status = "okay";
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
};
8、
&vcc3v3_lcd1_n {
gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
&wireless_wlan {
pinctrl-names = "default";
pinctrl-0 = <&wifi_host_wake_irq>;
WIFI,host_wake_irq = <&gpio2 RK_PB2 GPIO_ACTIVE_HIGH>;
};
&wireless_bluetooth {
compatible = "bluetooth-platdata";
clocks = <&pmucru CLK_RTC_32K>;
clock-names = "ext_clock";
//wifi-bt-power-toggle;
uart_rts_gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
pinctrl-names = "default", "rts_gpio";
pinctrl-0 = <&uart1m0_rtsn>;
pinctrl-1 = <&uart1_gpios>;
BT,reset_gpio = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
BT,wake_gpio = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
BT,wake_host_irq = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&xpcs {
status = "okay";
};
修改为：
&vcc3v3_lcd1_n {
gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
&wireless_wlan {
wifi_chip_type = "ap6275s";
status = "okay";
};
&wireless_bluetooth {
BT,wake_gpio = <&gpio3 RK_PB5 GPIO_ACTIVE_HIGH>;
BT,wake_host_irq = <&gpio2 RK_PD7 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&xpcs {
status = "okay";
};
相关的原理图：
